MAX987 Maxim, MAX987 Datasheet
MAX987
Available stocks
Related parts for MAX987
MAX987 Summary of contents
Page 1
... V . These open-drain versions CC EE are ideal for level translators and bipolar to single- ended converters. The single MAX987/MAX988 are available in tiny 5-pin SC70 packages, while the dual MAX991/MAX992 are available in ultra-small 8-pin SOT23 and µMAX ages. Selector Guide COMPARATORS ...
Page 2
... V ) ................................................... IN_-, IN_ .......................................-0. Current into Input Pins .....................................................±20mA OUT_ MAX987/MAX991/MAX995 ....................-0. MAX988/MAX992/MAX996 ..................................-0.3V to +6V OUT_ Short-Circuit Duration Continuous Power Dissipation (T = +70°C) A 5-Pin SC70 (derate 3.1mW/°C above +70°C) ...............247mW Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied ...
Page 3
... MAX987/MAX991/ MAX995 only 100mV overdrive C = 15pF, L MAX988/MAX992/ 10mV overdrive MAX996 only, 100mV overdrive R = 5.1kΩ PULLUP 10mV overdrive MAX987/MAX991/MAX995 only 15pF 100mV overdrive +25°C. Limits over the extended temperature range are guar +25°C.) A MIN TYP MAX ...
Page 4
High-Speed, Micropower, Low-Voltage, SOT23, Rail-to-Rail I/O Comparators (V = +5V 0V +25°C, unless otherwise noted SUPPLY CURRENT PER COMPARATOR vs. TEMPERATURE 90 V > V IN+ IN ...
Page 5
... V = 2.5.V CC 160 150 140 V = 5.5.V CC 130 120 110 100 -60 -40 - 100 TEMPERATURE (°C) MAX987/MAX991/MAX995 PROPAGATION DELAY (t ) PD+ MAX987- 50mV OD IN+ OUT 100ns/div MAX987/MAX991/MAX995 SWITCHING CURRENT, OUT RISING MAX987- 50mV OD IN+ OUT I CC 200ns/div 50mV/div 2V/div 50mV/div 2V/div 2mA/div 5 ...
Page 6
... SWITCHING CURRENT, OUT FALLING V OD IN+ OUT I CC 200ns/div 6 _______________________________________________________________________________________ Typical Operating Characteristics (continued) MAX987-14 = 50mV 50mV/div 2V/div 2mA/div POWER-UP DELAY MAX987- 50mV IN IN OUT 5µs/div 1MHZ RESPONSE MAX987-15 50mV/div IN+ OUT 2V/div V = 50mV OD 200ns/div 2V/div 2V/div ...
Page 7
... High-Speed, Micropower, Low-Voltage, SOT23, Rail-to-Rail I/O Comparators ______________________________________________________________Pin Description PIN MAX987 MAX991 MAX988 MAX996 SOT23/ SO/µMAX/ SO SC70 SOT23 1 6 — — — — — 1 — — 2 — — 3 — — 5 — — 6 — — 7 — — — ...
Page 8
... Unfortunately, this method also slows hysteresis response time. Use the following procedure to calcu- late resistor values for the MAX987/MAX991/MAX995. 1) Select R3. Leakage current under 10nA; therefore, the current through R3 should be at least 1µA to minimize errors caused by leakage current. ...
Page 9
... THR THF MAX988/MAX992/MAX996 The MAX988/MAX992/MAX996 have ±2.5mV internal hysteresis. They have open-drain outputs and require an external pullup resistor (Figure 2). Additional hys- teresis can be generated using positive feedback, but the formulas differ slightly from those of the MAX987/MAX991/MAX995 ...
Page 10
... High-Speed, Micropower, Low-Voltage, SOT23, Rail-to-Rail I/O Comparators Zero-Crossing Detector Figure 3 shows a zero-crossing detector application. The MAX987’s inverting input is connected to ground, and its noninverting input is connected to a 100mVp-p signal source. As the signal at the noninverting input crosses 0V, the comparator’s output changes state. ...
Page 11
High-Speed, Micropower, Low-Voltage, SOT23, Rail-to-Rail I/O Comparators Typical Application Circuit IN+ IN- MAX98_ MAX99_ REF * MAX988/MAX992/MAX996 ONLY THRESHOLD DETECTOR __________________________________________________Tape-and-Reel Information 1.5 +0.1/-0.0 DIAMETER 2.2 ±0.1 0.5 RADIUS TYPICAL B ...
Page 12
... High-Speed, Micropower, Low-Voltage, SOT23, Rail-to-Rail I/O Comparators (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) 12 ______________________________________________________________________________________ Package Information ...
Page 13
... Revision History Pages changed at Rev 2: 1–6, 8–13 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...