MAX14510E Maxim, MAX14510E Datasheet
MAX14510E
Related parts for MAX14510E
MAX14510E Summary of contents
Page 1
... The MAX14510E/MAX14511E feature a VBUS detection input (VB) to automatically switch to the USB signal path upon detection of a valid VBUS signal. The MAX14508E/ MAX14510E feature internal shunt resistors on the audio path to reduce clicks and pops heard at the output. The MAX14508E/MAX14509E/MAX14509AE have an enable input (EN) to reduce supply current and set all channels to high impedance when driven low. The MAX14508E– ...
Page 2
... Continuous Power Dissipation (T = +70°C) A 10-Pin UTQFN (derate 6.9mW/°C above +70°C).........559mW Note 1: Limits are only for the MAX14508E/MAX14509E/MAX14510E/MAX14511E. For the MAX14509AE (V from (V - 5.0V) to min of 6. Note 2: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four- layer board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial. Stresses beyond those listed under “ ...
Page 3
... 10mA CC UNC_ COM_ (Notes 3.0V 10mA -1. COM_ ANO_ +1.5V (Note 3. 10m ote MAX14508E/MAX14510E 10mA ANO_ V = 3.0V +2.5V, 0V; CC UNC_ V = -1.5V, +2.5V for COM_ EN CC MAX14508E/MAX14509E/MAX14509AE MAX14509E/MAX14511E/MAX14509AE 3.0V +2.5V, 0V ANO_ COM +2.5V MAX14508E/MAX14509E/MAX14509AE ...
Page 4
USB 2.0 Hi-Speed and Audio Switches with Negative Signal Capability ELECTRICAL CHARACTERISTICS (continued +2.7V to +5.0V -40°C to +85°C, unless otherwise noted. Typical values are PARAMETER SYMBOL Turn-Off Time t (Figure 2) ...
Page 5
... Note 4: The switch turns off for voltages above V Note 5: Guaranteed by design. Note 6: ΔR = ABS ON(MAX) ON(CH1) Note 7: Flatness is defined as the difference between the maximum and minimum value of on-resistance, as measured over specified analog signal ranges. Note 8: Between two switches. _______________________________________________________________________________________ with Negative Signal Capability CONDITIONS Human Body Model Human Body Model = +25° ...
Page 6
... USB 2.0 Hi-Speed and Audio Switches with Negative Signal Capability MAX14508E/ MAX14509E/ MAX14510E/ MAX14511E Figure 1. Fault Protection MAX14508E/ MAX14509E/ MAX14510E/ MAX14511E/ ANO_ V MAX14509AE IN_ OR UNC_ CONTROL LOGIC INPUT C INCLUDES FIXTURE AND STRAY CAPACITANCE OUT IN_ Figure 2. Switching Time ...
Page 7
... USB 2.0 Hi-Speed and Audio Switches MAX14508E/ MAX14509E/ UNC1 OR R MAX14510E/ S ANO1 MAX14511E/ V IN+ MAX14509AE UNC2 ANO2 V IN IN+ 50 50% IN PLHX OUT+ 50 50% V OUT PHLY Figure 3. Output Skew _______________________________________________________________________________________ with Negative Signal Capability ...
Page 8
... USB 2.0 Hi-Speed and Audio Switches with Negative Signal Capability COM1 MAX14508E/ UNC1 MAX14509E/ MAX14510E/ ANO1* 50Ω MAX14511E/ MAX14509AE OFF-ISOLATION IS MEASURED BETWEEN COM_ AND "OFF" ANO_ OR UNC_ TERMINAL ON EACH SWITCH. ON-LOSS IS MEASURED BETWEEN COM_ AND "ON" ANO_ OR UNC_ TERMINAL ON EACH SWITCH. ...
Page 9
USB 2.0 Hi-Speed and Audio Switches (V = 3.0V +25°C, unless otherwise noted UNC_ ON-RESISTANCE vs. V COM_ 2. 10mA UNC_ 2. 2.7V 2.50 CC 2.45 2.40 2. 5.0V CC ...
Page 10
... Negative Signal Capability (V = 3.0V +25°C, unless otherwise noted TOTAL HARMONIC DISTORTION PLUS NOISE vs. FREQUENCY 600Ω L 0.1 0.01 0.001 0.0001 0.01 0 FREQUENCY (MHz) PIN MAX14508E/ NAME MAX14510E/ MAX14509E/ MAX14511E MAX14509AE 1 1 UNC1 2 2 ANO2 3 3 ANO1 4 4 GND COM1 7 ...
Page 11
... USB 2.0 Hi-Speed and Audio Switches MAX14508E/MAX14509E/MAX14509AE Functional Diagrams/Truth Table UNC1 UNC2 ANO1 ANO2 EN MAX14508E/MAX14509E/MAX14509AE MAX14510E/MAX14511E Functional Diagrams/Truth Table UNC1 UNC2 ANO1 ANO2 VB > V VBDET < V VBDET Don’t Care ______________________________________________________________________________________ with Negative Signal Capability MAX14508E UNC1 COM1 UNC2 ...
Page 12
... COM_ rises above V protecting the switch and USB transceiver from damag- ing voltage levels. VBUS Detection Input The MAX14510E/MAX14511E feature a VBUS detection input (VB) that connects COM_ to UNC_ when V exceeds the VBUS detection threshold (V applications where VBUS is always present, drive the ...
Page 13
... C s STORAGE VOLTAGE 100pF CAPACITOR DC SOURCE Figure 5. Human Body ESD Test Model Power-Supply Sequencing Caution: Do not exceed the absolute maximum rat- ings because stresses beyond the listed ratings may cause permanent damage to the device. ______________________________________________________________________________________ with Negative Signal Capability I 100% P 90% ...
Page 14
... AUDIO AMPLIFIER ANO2 Chip Information PROCESS: BiCMOS 14 ______________________________________________________________________________________ 3.0V 0.1μ MAX14510E/ MAX14511E MAX14510E ONLY GND AOR For the latest package outline information and land patterns www.maxim-ic.com/packages. PACKAGE TYPE 10 Ultra-Thin QFN Typical Operating Circuit COM1 COMBINATION USB AND AUDIO CONNECTOR ...
Page 15
... NUMBER DATE 0 5/08 Initial release Released the MAX14510E, updated Absolute Maximum Ratings, Electrical 1 3/09 Characteristics, Figure 4, and Layout section. Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...