MAX4619 Maxim, MAX4619 Datasheet
MAX4619
Available stocks
Related parts for MAX4619
MAX4619 Summary of contents
Page 1
... Rev 2; 3/02 High-Speed, Low-Voltage, CMOS Analog ________________General Description The MAX4617/MAX4618/MAX4619 are high-speed, low- voltage, CMOS analog ICs configured as an 8-channel multiplexer (MAX4617), two 4-channel multiplexers (MAX4618), and three single-pole/double-throw (SPDT) switches (MAX4619). These CMOS devices can operate continuously with a +2V to +5.5V single supply. Each switch can handle ® ...
Page 2
... Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS— ...
Page 3
... Y_ Z_ MAX4617 1MHz MAX4618 Figure 7 MAX4619 MAX4617 1MHz MAX4618 Figure 7 MAX4619 R = 50Ω 100kHz, Figure 50Ω 100kHz, Figure 600Ω, 1Vp- 20Hz to 20kHz 5.5V ENABLE CC = +25°C.) (Note 2) ...
Page 4
High-Speed, Low-Voltage, CMOS Analog Multiplexers/Switches ELECTRICAL CHARACTERISTICS—Single +3.3V Supply (V = +3V to +3.6V 2.0V 0.5V PARAMETER SYMBOL ANALOG SWITCH Analog-Signal Range V ...
Page 5
... ON(MAX) ON(MIN) Note 4: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the specified analog signal ranges; i.e Note 5: Leakage parameters are 100% tested at maximum-rated hot operating temperature, and guaranteed by correlation at T Note 6: Guaranteed by design, not production tested. ...
Page 6
High-Speed, Low-Voltage, CMOS Analog Multiplexers/Switches (V = +5V, GND = +25°C, unless otherwise noted ON-RESISTANCE vs + +2.5V CC ...
Page 7
High-Speed, Low-Voltage, CMOS Analog (V = +5V, GND = +25°C, unless otherwise noted INPUT HIGH LOGIC THRESHOLD vs. SUPPLY VOLTAGE 1.8 1.6 1.4 1.2 1.0 2.0 2.5 3.0 3 TOTAL HARMONIC DISTORTION vs. ...
Page 8
... Note: Input and output pins are identical and interchangeable. Any may be considered an input or output; signals pass equally well in both directions. __________Applications Information Power-Supply Considerations The MAX4617/MAX4618/MAX4619 construction is typi- cal of most CMOS analog switches. They have two sup- ply pins: V and GND. V ...
Page 9
... Adjacent channel attenuation is about 3dB above that of a bare IC socket and is entirely due to capacitive coupling. _______________________________________________________________________________________ Multiplexers/Switches The MAX4617/MAX4618/MAX4619 are pin compatible with the industry-standard 74HC4051/74HC4052/ 74HC4053 and the MAX4581/MAX4582/MAX4583. In single-supply applications, they function identically and have identical logic diagrams, although these parts dif- Power Supply fer electrically ...
Page 10
... All switches open L X–X0 H X–X1 L X–X2 H X–X3 L X–X4 H X–X5 L X–X6 H X–X7 MAX4618 MAX4619 All switches open X–X0, X–X0, Y–Y0, Y–Y0 Z–Z0 X–X1, X–X1, Y–Y0, Y–Y1 Z–Z0 X–X0, X–X2, Y–Y1, Y–Y2 Z–Z0 X–X1, X–X3, Y– ...
Page 11
... X1, X2, Y1, 50Ω Y2. X3, Y3 MAX4618 ENABLE GND X1, Y1 50Ω MAX4619 X2, Y2, Z2 ENABLE GND TEST EACH SECTION INDIVIDUALLY. Figure 2. Address Transition Times ______________________________________________________________________________________ Multiplexers/Switches X1– OUT V OUT 35pF 300Ω ...
Page 12
... X0 X1–X3, Y1–Y3 MAX4618 V ENABLE ENABLE GND 50Ω X1, Y1 X0, Y0, Z0 MAX4619 V ENABLE ENABLE GND 50Ω TEST EACH SECTION INDIVIDUALLY. Figure 3. Enable Switching Times 12 ______________________________________________________________________________________ V V ENABLE OUT X OUT 35pF 300Ω ...
Page 13
... Y1, Z0, Z1 50Ω MAX4619 ENABLE GND TEST EACH SECTION INDIVIDUALLY. Figure 4. Break-Before-Make Interval X_, Y_ CHANNEL B SELECT MAX4617 C MAX4618 MAX4619 V ENABLE ENABLE GND 50Ω TEST EACH SECTION INDIVIDUALLY. Figure 5. Charge Injection ______________________________________________________________________________________ Multiplexers/Switches 50Ω OUT 35pF 300Ω ...
Page 14
... OFF ISOLATION IS MEASURED BETWEEN COM AND "OFF" NO TERMINAL ON EACH SWITCH. ON LOSS IS MEASURED BETWEEN COM AND "ON" NO TERMINAL ON EACH SWITCH. CROSSTALK (MAX4618/MAX4619) IS MEASURED FROM ONE CHANNEL ( ALL OTHER CHANNELS. SIGNAL DIRECTION THROUGH SWITCH IS REVERSED; WORST VALUES ARE RECORDED. Figure 6. Off-Isolation, On-Loss, and Crosstalk ...
Page 15
... MAX4619CUE 0°C to +70°C MAX4619CSE 0°C to +70°C MAX4619CPE 0°C to +70°C MAX4619EGD -40°C to +85°C MAX4619EUE -40°C to +85°C MAX4619ESE -40°C to +85°C MAX4619EPE -40°C to +85°C ______________________________________________________________________________________ Multiplexers/Switches ___________________Chip Information PIN-PACKAGE 16 QFN TRANSISTOR COUNT: 244 16 TSSOP ...
Page 16
... For the latest package outline information, Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...