MAX4888C Maxim, MAX4888C Datasheet
MAX4888C
Related parts for MAX4888C
MAX4888C Summary of contents
Page 1
... PCI Express data between two possible destinations. These devices feature a dual digital control input to switch signal paths. The MAX4888C is intended for use in systems where both the input and output are capacitively coupled (e.g., SAS, SATA, XAUI, and PCIe) and provides a 10FA (typ) source current and a 60kI (typ) internal biasing resistor to GND at the AOUT_ and BOUT_ pins ...
Page 2
... V = +3. AIN_ BIN_ _OUTA_ _OUTB_ AIN_ unconnected (MAX4888B) All other ports are unconnected (MAX4888C) All other ports are unconnected (MAX4888C) = +70NC GND are clamped 3.3V +25NC, unless otherwise CC A MIN TYP MAX V CC -0.3 1.8 = 15mA, 6.4 8.4 = 15mA, 0 ...
Page 3
... Note ON(MAX) ON(MIN) Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the specified analog-signal range. Note 6: Guaranteed by design; not production tested. unless otherwise noted. Typical values are CONDITIONS Z ...
Page 4
... THE FREQUENCY OF THE SIGNAL SHOULD BE ABOVE THE HIGHPASS FILTER CORNER OF THE COUPLING CAPACITORS. Figure 1. Switching Time Table 1. Insertion Loss Mask FREQUENCY RANGE (GHz 2.5 2 Greater than 8 4 Test Circuits/Timing Diagrams SOURCE LOAD MAX4888B MAX4888C OUT Σ SEL 50% 50% 90% MAXIMUM INSERTION LOSS (dB ...
Page 5
... SC CALp CALn OUTp OUTn V OUTp V OUTn AFTER ELIMINATING SOURCE AND CABLE SKEWS. Figure 2. Propagation Delay and Output Skew Test Circuits/Timing Diagrams (continued) SOURCE LOAD MAX4888B MAX4888C OUTp OUTn Σ S- SEL Z S CALIBRATION V CALp Z S TRACES V CALn Σ ...
Page 6
... 3.0V CC 150 100 1.5 -40 - TEMPERATURE (°C) DIFFERENTIAL RETURN LOSS vs. FREQUENCY 0 MASK -10 -20 -30 -40 -50 -60 -70 MAX4888B -80 3.5 3 FREQUENCY (GHz) DIFFERENTIAL CROSSTALK vs. FREQUENCY 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 FREQUENCY (GHz) MAX4888C 60 85 MAX4888C ...
Page 7
... Analog Switch 1, Normally Closed Positive Terminal 24 SEL Control Signal Input. SEL has a 70kI (typ) pulldown resistor to GND. — EP Exposed Pad. Connect EP to GND GND MAX4888B MAX4888C CC GND TQFN FUNCTION ...
Page 8
... BOUTB- AIN_, BIN_ AIN_, BIN_ SEL SELB TO AOUTA_, TO AOUTB_, BOUTA_ BOUTB_ 0 (DEFAULT) 0 OFF OFF ON 0 (DEFAULT) 1 (DEFAULT) ON OFF 1 1 (DEFAULT) OFF MAX4888C AIN+ AOUTA+ AIN- AOUTA- AOUTB+ AOUTB- BIN+ BOUTA+ BIN- BOUTA- BOUTB+ BOUTB SELB CONTROL SEL GND ...
Page 9
... MAX4888C features a 10FA (typ) source current and a 60kI (typ) internal biasing resistor to GND at the AOUTA_, BOUTA_, AOUTB_, and BOUTB_ terminals. The MAX4888C is ideal for circuits that are capacitively coupled at both the output and input. These devices are protocol independent and can be used to switch two dif- ferent protocol signals over the same physical lane ...
Page 10
... Initial release Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ...