MAX4531 Maxim, MAX4531 Datasheet
MAX4531
Available stocks
Related parts for MAX4531
MAX4531 Summary of contents
Page 1
... All devices have two complementary switch-enable inputs and address latching. The MAX4530/MAX4531/MAX4532 operate from a sin- gle supply of +2V to +12V, or from dual supplies of ±2V to ±6V. On-resistance (150Ω max) is matched between switches to 8Ω max. Each switch can handle rail-to-rail analog signals ...
Page 2
... COM A MAX4531 4.5V, ± NO MAX4532 V+ = 5.5V -5. +25° ±4.5V, COM MAX4530 5.5V -5.5V MAX4531 T = +25°C MAX4531/ A MAX4532 +70° 0.8V unless EN_L A MIN MAX MIN TYP MAX (Note 100 MIN MAX ...
Page 3
Low-Voltage, CMOS Analog Multiplexers/Switches with Enable Inputs and Address Latching ELECTRICAL CHARACTERISTICS—Dual Supplies (continued) (V+ = +5V ±10 -5V ±10%, GND = 0, V otherwise noted.) PARAMETER SYMBOL DIGITAL LOGIC INPUT ADD_H EN_H Logic High ...
Page 4
... COM MAX4530 V = 4.5V, 1V; COM 1V, 4.5V MAX4531 5.5V MAX4532 MAX4530 T A MAX4531 T MAX4531/ A MAX4532 0.8V unless EN_L A MIN MAX MIN TYP MAX (Note 2) = +25°C 0.025 = +25° +25° +25° +25°C ...
Page 5
Low-Voltage, CMOS Analog Multiplexers/Switches with Enable Inputs and Address Latching ELECTRICAL CHARACTERISTICS—Single +5V Supply (continued) (V+ = +5V ±10 GND = 0, V otherwise noted.) PARAMETER SYMBOL DIGITAL LOGIC INPUT V , ADD_H Logic-High Threshold V , ...
Page 6
... Select to Latch Enable) Hold Time, Latch Enable Channel Select Pulse Width, Latch Enable t MPW Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in this data sheet. Note 3: Guaranteed by design. Note 4: ∆ (max (min). ON ...
Page 7
Low-Voltage, CMOS Analog Multiplexers/Switches with Enable Inputs and Address Latching __________________________________________Typical Operating Characteristics (T = +25°C, unless otherwise noted.) A ON-RESISTANCE vs. V COM (DUAL SUPPLIES) 100 90 V± = ±2. V± = ± V± = ...
Page 8
... Low-Voltage, CMOS Analog Multiplexers/Switches with Enable Inputs and Address Latching ______________________________________________________________Pin Description PIN MAX4530 MAX4531 — 16, 17, 18, 19 — — — — — — — 4 — — — 17 — — ...
Page 9
... The V+ and V- sup- plies need not be symmetrical, but their sum cannot exceed the +13V absolute maximum rating. The MAX4530/MAX4531/MAX4532 operate from a sin- gle supply between +2V and +12V when V- is connect GND. All of the bipolar precautions must be observed ...
Page 10
... ADD_ ADDC NO1–NO6 ADDB 50Ω ADDA MAX4530 V+ EN2 EN1 GND ADD_ ADDA NO1_, NO2_ ADDB 50Ω MAX4531 V+ EN2 EN1 GND ADD_ ADD_ 50Ω MAX4532 V+ EN2 EN1 GND Figure 1. Address Transition Time 10 ______________________________________________________________________________________ +3V NO0 V ADD_ ...
Page 11
... ADDC NO1–NO7 ADDB ADDA MAX4530 V EN1 EN1 V+ EN2 50Ω GND ADDA NO1_, N02_, NO3_ ADDB MAX4531 V EN1 EN1 V+ EN2 50Ω GND ADD_ MAX4532 V EN1 EN1 V+ EN2 GND 50Ω FOR SINGLE-SUPPLY OPERATION. REPEAT TEST FOR EACH SECTION. ...
Page 12
... ADDC NO0–NO7 ADDB 50Ω ADDA MAX4530 V+ EN2 EN1 GND ADD_ ADDA NO0_–NO3_ ADDB 50Ω MAX4531 V+ EN2 EN1 GND ADD_ NO_, NC_ ADD_ 50Ω MAX4532 V+ EN2 EN1 GND FOR SINGLE-SUPPLY OPERATION. REPEAT TEST FOR EACH SECTION. ...
Page 13
... OFF ISOLATION IS MEASURED BETWEEN COM_ AND OFF NO_ TERMINAL ON EACH SWITCH. ON LOSS IS MEASURED BETWEEN COM_ AND ON TERMINAL ON EACH SWITCH. CROSSTALK (MAX4531/MAX4532 IS MEASURED FROM ONE CHANNEL ( ALL OTHER CHANNELS. SIGNAL DIRECTION THROUGH SWITCH IS REVERSED; WORST VALUES ARE RECORDED. Figure 5. Off Isolation, On Loss, and Crosstalk ...
Page 14
... ADD_ ADDC ADDB 50Ω ADDA MAX4530 50Ω EN1 GND V+ EN2 V+ V ADD_ ADDA NO1_, NO2_, NO3_ ADDB 50Ω MAX4531 50Ω EN1 GND V+ EN2 V+ V ADD_ ADD_ 50Ω MAX4532 LE 50Ω EN1 GND FOR SINGLE-SUPPLY OPERATION. ...
Page 15
... X = Don’t Care *ADDC not present on MAX4531. Note: NO_ and COM_ pins are identical and interchangeable. Either may be considered an input or an output; signals pass equally well in either direction independent of EN1 and EN2. ______________________________________________________________________________________ ADDA MAX4530 X Last address ...
Page 16
... MAX4531CPP 0°C to +70°C MAX4531CWP 0°C to +70°C MAX4531CAP 0°C to +70°C MAX4531C/D 0°C to +70°C MAX4531EPP -40°C to +85°C MAX4531EWP -40°C to +85°C MAX4531EAP -40°C to +85°C *Contact factory for availability. __________________________________________________________Chip Topographies MAX4530/MAX4532 NO3 (NCB) V+ NO1 (NOB) NO2 (COMB) ...