MAX4588 Maxim, MAX4588 Datasheet
MAX4588
Available stocks
Related parts for MAX4588
MAX4588 Summary of contents
Page 1
... SPI™/ MICROWIRE™ serial port. Each channel of the MAX4588 is designed using a “T” switch configuration, ensuring excellent high-frequency off-isolation. The MAX4588 has low on-resistance of 60Ω max, with an on-resistance match across all chan- nels of 4Ω ...
Page 2
... SSOP (derate 9.52mW/°C above +70°C) ....................762mW Wide SO (derate 12.50mW/°C above +70°C)................1.00W Plastic DIP (derate 14.29mW/°C above +70°C) ............1.14W Operating Temperature Ranges MAX4588C_ I ......................................................0°C to +70°C MAX4588E_ I ...................................................-40°C to +85°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10sec) .............................+300°C = +2.4V +0.8V, T ...
Page 3
Dual 4-Channel RF/Video Multiplexer ELECTRICAL CHARACTERISTICS—Dual Supplies (continued) ( +4.5V to +5.5V -4.5V to -5.5V ues are +25° +5V -5V.) (Note ...
Page 4
Low-Voltage, High-Isolation, Dual 4-Channel RF/Video Multiplexer ELECTRICAL CHARACTERISTICS—Dual Supplies (continued) ( +4.5V to +5.5V -4.5V to -5.5V ues are +25° +5V -5V.) (Note 2) ...
Page 5
Dual 4-Channel RF/Video Multiplexer ELECTRICAL CHARACTERISTICS—Single +5V Supply (continued) ( +4.5V to +5.5V INH = +25° +5V.) (Note 2) L PARAMETER SYMBOL SWITCH DYNAMIC CHARAC- SWITCH DYNAMIC CHARACTERISTICS ...
Page 6
Low-Voltage, High-Isolation, Dual 4-Channel RF/Video Multiplexer ELECTRICAL CHARACTERISTICS—Single +5V Supply (continued) ( +4.5V to +5.5V INH = +25° +5V.) (Note 2) L PARAMETER SYMBOL POWER SUPPLY POWER SUPPLY ...
Page 7
... ON ON(MAX) ON(MIN) Note 5: Resistance flatness is defined as the difference between the maximum and the minimum value of on-resistance as measured over the specified analog-signal range. Note 6: Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at T Note 7: Off isolation = 20log ...
Page 8
Low-Voltage, High-Isolation, Dual 4-Channel RF/Video Multiplexer ( +5V -5V +25°C, unless otherwise noted ON-RESISTANCE vs. V COM (DUAL SUPPLIES) 100 90 ±2.5V 80 ± ±4V 50 ± ...
Page 9
Dual 4-Channel RF/Video Multiplexer ( +5V -5V +25°C, unless otherwise noted ON/OFF TIME vs. SUPPLY VOLTAGE 600 500 t ON 400 300 200 t OFF 100 0 2.5 3.0 3.5 4.0 ...
Page 10
Low-Voltage, High-Isolation, Dual 4-Channel RF/Video Multiplexer PIN NAME 21, GND Ground. Connect all ground pins to a ground plane. See Grounding section. 23 COM1 Analog Switch Common Terminal. See Truth Table Analog ...
Page 11
... V+ V+ LE/CS MAX4588 EN COM_ V- V- Figure 1. Turn-On/Turn-Off Time V+ V+ LE/CS SER/PAR MAX4588 A0 COM_ V- V- Figure 2. Break-Before-Make Time Delay V+ NO_ V+ LE/CS SER/PAR MAX4588 EN COM_ GND V- V- Figure 3. Charge Injection ______________________________________________________________________________________ Low-Voltage, High-Isolation, NO_ V NO_ V OUT 30pF 300 GND NO_ NO_ V NO_ V OUT 30pF 300 ...
Page 12
... NOTE: ALL INPUT SIGNALS ARE SPECIFIED WITH t Figure 6. Parallel Timing Diagram 12 ______________________________________________________________________________________ MAX4588 1MHz CAPACITANCE ANALYZER 49.9 56 24.9 560 = 0dB AND t <10ns. TIMING IS MEASURED FROM 50% OF DIGITAL SIGNAL NO_ 1MHz CAPACITANCE ANALYZER FLOATING COM_ GND MEASURE NODE 50 MEASURE NODE 50 MAX4588 ...
Page 13
... All of these capacitances are distributed evenly along the series resistance, so they act as a transmis- sion line rather than a simple R-C filter. The MAX4588’s construction allows an exceptional 180MHz bandwidth when the switches are on. ...
Page 14
... Voltages below -0.3V can be clipped by the internal ESD-protection diodes, and the parts can be damaged if excessive current flows. When power to the MAX4588 is off (i.e and V- = 0), the Absolute Maximum Ratings still apply. This means that none of the MAX4588 pins can exceed ± ...
Page 15
... The MAX4588 is intended for use in 75Ω systems, where the inputs are terminated external to the IC and the COM terminals see an impedance of 600Ω or high- er. The MAX4588 can operate in 50Ω and 75Ω systems with terminations through the IC. However, variations in R and R ...
Page 16
... CS, so all four MAX4588s change state simultaneously. The parallel mode is activated by driving SER/PAR to a logic low. The MAX4588 is programmed by a latched parallel bus scheme. Refer to Figure 6 for a detailed diagram of the parallel-interface logic. Note that 4/8 is not latched ...
Page 17
... Don’t Care Note: DISABLE, A2, A1, and A0 are the 4 bits latched into the MAX4588 with a MICROWIRE/SPI write the LSB (first bit in time). DISABLE is the MSB (last bit in time). ______________________________________________________________________________________ Low-Voltage, High-Isolation DOUT ...
Page 18
Low-Voltage, High-Isolation, Dual 4-Channel RF/Video Multiplexer ____________________Chip Information TRANSISTOR COUNT: 1033 18 ______________________________________________________________________________________ Package Information ...
Page 19
Low-Voltage, High-Isolation, Dual 4-Channel RF/Video Multiplexer ______________________________________________________________________________________ Package Information (continued) 19 ...
Page 20
... Low-Voltage, High-Isolation, Dual 4-Channel RF/Video Multiplexer Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 20 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © ...