APE1630 Advanced Power Electronics Corp., APE1630 Datasheet
APE1630
Specifications of APE1630
Related parts for APE1630
APE1630 Summary of contents
Page 1
... LED chain voltage. The device operates from an input supply between 8V and 32V and provides an externally adjustable output current 1A. Depending upon the supply voltage and external components, the APE1630 can provide more than 15 watts of output power. The APE1630 includes the power switch and a high-side output current sensing circuit, which uses an external resistor to set the nominal average output current, and a dedicated DIM input accepts a wide range of pulsed dimming ...
Page 2
... Advanced Power Electronics Corp. BLOCK DIAGRAM VIN CSN 70µ DIM PIN ASSIGNMENT The package of APE1630 is SOT-89-5L; the pin assignment is given by: (Top View) VIN CSN 5 4 GND APE1630 GND DIM SOT-89-5L ORDER/MARKING INFORMATION Order Information APE1630X Package Type G5 : SOT-89-5L V25 ...
Page 3
... V V –V CSN IN CSN V CSN_hys I V –V = 50mV CSN IN CSN V DIM_H V DIM_L 500kHz DIM OSC f = 100Hz DIM D PWM_LF APE1630 Rating Unit -0 -0 +0.3 to (-6. 1.2 A 1.5 W -40 to 125 °C -55 to 150 °C 15 °C/W 50 °C/W (Multi-layer). 2 Min Typ Max Units 8 - ...
Page 4
... DIM DIM_L DIM 0.3A SAT OUT 0.8A SAT OUT I SWmean I LEAK SD-hys R S 0.4 V CSN IN DIM APE1630 GND 130 I = CSN = = . 0 325 A LED APE1630 25 300 - KΩ µA - 0.8 1 1 0.5 5 µA - 150 - ° ° LED 47uH ...
Page 5
... The APE1630 allow dimming with a PWM signal at the DIM input. A logic level below 0.3V at DIM forces APE1630 to turn off the LED and the logic level at DIM must be at least 2.0V to turn on the full LED current. The frequency of PWM dimming ranges from 100Hz to more than 20 kHz. The DIM pin is pulled high current approximately 70µ ...
Page 6
... LED color does not vary with brightness as it does with analog dimming. Pulsing the current provides precise brightness control while preserving the color purity. The dimming frequency of APE1630 can be as high as 20 kHz. Shutdown mode Taking the DIM pin to a voltage below 0.3V will turn off the output and the supply current will fall to a low standby level of 70µ ...
Page 7
... Inductor selection Recommended inductor values for the APE1630 are in the range 47uH to 120uH. Higher values of inductance are recommended at lower output current in order to minimize errors due to switching delays, which result in increased ripple and lower efficiency. Higher values of inductance also result in a smaller change in output current over the supply voltage range ...
Page 8
... This prevents the switch working with excessive 'on' resistance under conditions where the duty cycle is high. Thermal shutdown protection To ensure the reliability, the APE1630 is built with a thermal shutdown (TSD) protection function. The TSD protests the IC from over temperature (150°C). When the chip temperature decreases (115°C), the IC recovers again. ...
Page 9
... Temperature 1 0.98 0.96 0.94 0.92 0 500 400 300 200 100 =12V IN APE1630 V VS IMMING HRESHOLD OLTAGE ↑ Turn On ↓ Turn Off ( VS. FREQUENCY (L=120µ ...
Page 10
... Advanced Power Electronics Corp. TYPICAL CHARACTERISTICS (CONTINUOUS) 50KHz Dimming V IN 1KHz Dimming =32V 50KHz Dimming V APE1630 =12V IN 10 ...
Page 11
... REF. 1.50 REF. 0.46 0.52 0.016 1.50 1.60 0.055 0.39 0.43 0.014 5 TYP. o 0.47 0.51 0.017 0.18 0.21 0.006 0.57 0.63 0.020 0.16 0.19 0.005 APE1630 1.8 0.6 0.6 1.5 L Dimensions in Inches Nom. Max. 0.177 0.185 0.163 0.167 0.067 0.079 0.098 0.106 0.035 0.039 0.118 REF. 0.059 REF. 0.018 0.020 0.059 0.063 0.015 0.017 5 TYP. o 0.019 0.020 0.007 ...