TLE 4699E Infineon Technologies, TLE 4699E Datasheet
TLE 4699E
Specifications of TLE 4699E
Related parts for TLE 4699E
TLE 4699E Summary of contents
Page 1
Low Drop Out Linear Voltage Regulator 5 V Fixed Output Voltage Rev. 1.0, 2010-11- ...
Page 2
Table of Contents 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 3
Low Drop Out Linear Voltage Regulator 5 V Fixed Output Voltage 1 Overview Features Output Voltage 5 V ± 2% • • Current Capability 200 mA • Ultra Low Current Consumption • Very Low Drop Out Voltage • Enable Function: ...
Page 4
Block Diagram j I Protection Circuits EN SI Block_ diagram.vsd Figure 1 Block Diagram TLE4699 Data Sheet TLE4699 Bandgap Reference Generator GND 4 TLE4699 Block Diagram Q SO Reset RO RADJ D Rev. 1.0, 2010-11-30 ...
Page 5
Pin Configuration 3.1 Pin Assignment TLE4699GM (PG-DSO-14 Figure 2 Pin Configuration PG-DSO-14 Package (top view) 3.2 Pin Definitions and Functions TLE4699GM (PG-DSO-14) Pin Symbol Function 1 RADJ Reset Threshold Adjust Connect an external voltage divider to adjust reset threshold; ...
Page 6
Pin Symbol Function 13 I Regulator Input and IC Supply for compensating line influences, a capacitor to GND close to the IC pin is recommended Sense Input Connect the voltage rail to be monitored; Connect ...
Page 7
Pin Assignment TLE4699E Figure 3 Pin Configuration PG-SSOP-14 EP Package (top view) 3.4 Pin Definitions and Functions TLE4699E (PG-SSOP-14 EP Pin Symbol Function 1 RADJ Reset Threshold Adjust Connect an external voltage divider to adjust reset threshold; Connect to ...
Page 8
Pin Symbol Function n.c. Not connected 10, 12 Internally not connected; Connection to PCB GND recommended. PAD Exposed Pad Attach the exposed pad on package bottom to the heatsink area on circuit board; Connect to GND Data ...
Page 9
General Product Characteristics 4.1 Absolute Maximum Ratings 1) Absolute Maximum Ratings T = -40 °C to +150 °C; all voltages with respect to ground, positive current flowing into pin j (unless otherwise specified) Pos. Parameter Voltage Rating 4.1.1 Regulator ...
Page 10
Functional Range Pos. Parameter 4.2.1 Input Voltage Range for Normal Operation 4.2.2 Extended Input Voltage Range 4.2.3 Input Voltage Transient Immunity 4.2.4 Junction Temperature 4.2.5 Output Capacitor Requirements 4.2.6 1) For specification of the input voltage 2) The output ...
Page 11
Thermal Resistance Pos. Parameter TLE4699GM Package PG-DSO-14 4.3.1 Junction to Soldering Point 4.3.2 Junction to Ambient 4.3.3 4.3.4 4.3.5 TLE4699E Package PG-SSOP-14 EP 4.3.6 Junction to Soldering Point 1) 4.3.7 Junction to Ambient 4.3.8 4.3.9 4.3.10 1) Not subject ...
Page 12
Voltage Regulator 5.1 Description Voltage Regulator V The output voltage is controlled by comparing a portion internal reference and driving a PNP pass Q transistor accordingly. Saturation control as a function of the load current ...
Page 13
Electrical Characteristics Voltage Regulator Electrical Characteristics: Voltage Regulator 13 -40 °C to +150 ° all voltages with respect to ground, direction of currents as shown in Pos. Parameter 5.2.1 Output Voltage 5.2.2 ...
Page 14
Typical Performance Characteristics Voltage Regulator V Output Voltage vs Junction Temperature j V [V] Q 5.02 5.00 4.98 4.96 -40 - Output Current Limitation Q,max V vs. Input Voltage I I Q,ma ...
Page 15
V Dropout Voltage vs Output Current Q V [mV] dr 200 T = 125 °C 100 ° 0 Reverse Output Current vs Output Voltage [mA] ...
Page 16
Current Consumption 6.1 Electrical Characteristics Current Consumption Electrical Characteristics: Current Consumption 13 -40 °C to +150 °C, all voltages with respect to ground, direction of currents as shown Figure 6 “Parameter ...
Page 17
Typical Performance Characteristics Current Consumption I Current Consumption vs Junction Temperature j I [mA 150 0.1 0.01 -40 -20 ...
Page 18
Enable Function 7.1 Description Enable Function The TLE4699 can be turned on or turned off via the EN Input. With voltage levels higher than the EN Input the device will be completely turned on. A voltage level lower than ...
Page 19
Typical Performance Characteristics Enable Input I Enable Input Current vs Enable Input Voltage ° [µ Data Sheet Enable Input Current vs. ...
Page 20
Reset Function 8.1 Description Reset Function The reset function contains several features: Output Undervoltage Reset: An output undervoltage condition is indicated by setting the reset output “RO” to “low”. This signal might be used to reset a microcontroller during ...
Page 21
Reset Reaction Time In case the output voltage of the regulator drops below the output undervoltage lower reset threshold C delay capacitor is discharged rapidly. Once the delay capacitor’s voltage has reached the lower delay switching D V threshold , ...
Page 22
Supply I Control GND Figure 7 Block Diagram Reset Circuit RT,hi V RT RO,low Thermal Shutdown Figure 8 Timing ...
Page 23
Electrical Characteristics Reset Function Electrical Characteristics: Reset Function 13 -40 °C to +150 ° all voltages with respect to ground, direction of currents as shown in Pos. Parameter Output Undervoltage Reset Comparator ...
Page 24
Electrical Characteristics: Reset Function (cont’ 13 -40 °C to +150 ° all voltages with respect to ground, direction of currents as shown in Pos. Parameter 8.2.15 Power-on Reset Delay Time 8.2.16 Internal Reset ...
Page 25
Early Warning Function 9.1 Description Early Warning Function The additional sense comparator provides an early warning function: Any voltage (e.g. the input voltage) can be monitored, an undervoltage condition is indicated by setting the comparator’s output to low. The ...
Page 26
Early Warning Resistor Divider Adjust The switching threshold can be set to the application’s needs by connecting an external voltage divider ( at pin “SI”. If the Early Warning function is not needed recommend to connect the SI ...
Page 27
Electrical Characteristics Early Warning Function Electrical Characteristics: Early Warning Function 13 -40 °C to +150 °C, all voltages with respect to ground, direction of currents as shown (unless otherwise specified) Pos. ...
Page 28
Package Outlines 1.27 2) +0.10 0.41 -0. 8.75 Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Lead width can be 0.61 max. in dambar area Figure 11 Outline PG-DSO-14 ...
Page 29
4.9 ±0.1 Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Does not include dambar protrusion Figure 12 Outline PG-SSOP-14 EP Green ...
Page 30
Revision History Revision Date Changes 1.0 2010-11-30 Data sheet Data Sheet 30 TLE4699 Revision History Rev. 1.0, 2010-11-30 ...
Page 31
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...