MGA-82563 Avago Technologies, MGA-82563 Datasheet
MGA-82563
Available stocks
Related parts for MGA-82563
MGA-82563 Summary of contents
Page 1
... MGA-82563 0.1– 6 GHz dBm Amplifier Data Sheet Description Avago’s MGA-82563 is an economical, easy-to-use GaAs MMIC amplifier that offers excellent power and low noise figure for applications from 0 GHz. Pack- aged in an ultra-miniature SOT-363 package, it requires half the board space of a SOT-143 package. ...
Page 2
... MGA-82563 Absolute Maximum Ratings Symbol Parameter V Device Voltage, RF Output d to Ground V Device Voltage, Gate gd to Drain V Range of RF Input Voltage in to Ground Input Power in T Channel Temperature ch T Storage Temperature STG MGA-82563 Electrical Specifications, Symbol Parameters and Test Conditions [1] G Gain in test circuit ...
Page 3
... MGA-82563 Typical Performance +85° +25° –40° FREQUENCY (GHz) Figure 1. 50 Ω Power Gain vs. Frequency and Temperature FREQUENCY (GHz) Figure 4. 50 Ω ...
Page 4
... MGA-82563 Typical Noise Parameters = 50 Ω 25° Frequency NF O GHz dB 0.5 2.10 1.0 2.10 1.5 2.10 2.0 2.12 2.5 2.12 3.0 2.15 3.5 2.16 4.0 2.16 4.5 2.19 5.0 2.18 5.5 2.19 6.0 2.23 6.5 2.28 7.0 2.39 Note: 1. Reference plane per Figure 11 in Applications Information section Ω 25° Mag Ang ...
Page 5
... Introduction This medium power GaAs MMIC amplifier was devel- oped for commercial wireless applications from 100 MHz to 6 GHz. The MGA-82563 runs on only 3 volts and typically requires only deliver over 17 dBm of output power gain compression. The 17.3 dBm output power (P ...
Page 6
... To assist designers in optimizing not only the immedi- ate circuit using the MGA-82563, but to also optimize and evaluate trade-offs that affect a complete wireless system, the standard deviation (σ) is provided for many of the Electrical Specifications parameters (at 25°) in addition to the mean. The standard deviation is a measure of the variability about the mean ...
Page 7
... Figure 15. DC blocking capacitors (C1 and C2) are used at the input and output of the MMIC to isolate the device from adjacent circuits. While the input terminal of the MGA-82563 is at ground potential not a current sink. If the input is connected to a preceding stage that has a voltage present, the use of the DC blocking capacitor (C1) is required ...
Page 8
... This is normal and is taken into account for the PAE data in Figure 17. Like other active devices, the intermodulation prod- ucts of the MGA-82563 increase as the device is driven further into nonlinear operation. The 3rd, 5th, and 7th order intermodulation products of the MGA-82563 are shown in Figure 18 along with the fundamental response ...
Page 9
... SOT-363 PCB Footprint A recommended PCB pad layout for the miniature SOT- 363 (SC-70) package used by the MGA-82563 is shown in Figure 21 (dimensions are in inches). This layout provides ample allowance for package placement by automated assembly equipment without adding parasitics that could impair the high frequency RF performance of the MGA-82563 ...
Page 10
... Device Orientation REEL CARRIER USER FEED DIRECTION COVER TAPE Part Number Ordering Information Part Number MGA-82563-TR1 MGA-82563-BLK NOTES: 1. All dimensions are in mm. 2. Dimensions are inclusive of plating. 3. Dimensions are exclusive of mold flash & metal burr. 4. All specifications comply to EIAJ SC70. ...
Page 11
... For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries. Data subject to change. Copyright © 2006 Avago Technologies, Limited. All rights reserved. Obsoletes 5989-4584EN AV01-0198EN May 19, 2006 D ...