CM1402 California Micro Devices, CM1402 Datasheet
CM1402
Available stocks
Related parts for CM1402
CM1402 Summary of contents
Page 1
... California Micro Devices Corp. All rights reserved. 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ▲ Tel: 408.263.3214 05/19/04 Product Description CAMD's CM1402 is an EMI filter array with ESD pro- tection, which integrates three pi filters (C-R-C) and two additional channels of ESD protection. CM1402 has component values of 20pF-47Ω-20pF, and 20pF-100Ω ...
Page 2
... Ordering Part 1 Number Part Marking CM1402-03CS CE + " character for the top side orientation mark. ▲ Fax: 408.263.7846 CM1402 BOTTOM VIEW (Bumps Up View) Orientation Marking Supply Lead-free Finish Ordering Part 1 Number Part Marking CM1402-03CP ▲ www.calmicro.com 2 CE 05/19/04 ...
Page 3
... IN 30mV 10µ 3.3V BIAS I = 10mA LOAD I = -10mA LOAD Notes 2,4 and 5 Notes 2,3,4 and 100Ω 20pF = 50Ω 47Ω 20pF = 50Ω ▲ Tel: 408.263.3214 CM1402 RATING -65 to +150 100 300 RATING -40 to +85 1 MIN TYP MAX 80 100 120 ...
Page 4
... Typical Filter Performance (nominal conditions unless specified otherwise, 50 Ohm Environment) © 2004 California Micro Devices Corp. All rights reserved. 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ▲ Tel: 408.263.3214 4 Figure 1. A1-C1 EMI Filter Performance Figure 2. A2-C2 EMI Filter Performance ▲ Fax: 408.263.7846 CM1402 ▲ www.calmicro.com 05/19/04 ...
Page 5
... Typical Filter Performance (nominal conditions unless specified otherwise, 50 Ohm Environment) Figure 4. Typical Diode Capacitance vs. Input Voltage (normalized to 2.5VDC) © 2004 California Micro Devices Corp. All rights reserved. 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 05/19/04 Figure 3. A3-C3 EMI Filter Performance ▲ Tel: 408.263.3214 CM1402 ▲ ▲ Fax: 408.263.7846 www.calmicro.com 5 ...
Page 6
... VCC supply (5V, 3.3V or 1.8V) GND For information on the assembly of the CM1402 to the PCB (printed circuit board), please refer to the Chip µ Scale Package (CSP) Application Note AP217, or con- tact factory at 800-325-4966 for technical support. ▲ Fax: 408.263.7846 CM1402 Figure 5 ...
Page 7
... DIA. Solder Mask Opening 0.325mm DIA. 250 200 150 100 50 0 Figure 8. Lead-free (SnAgCu) Solder ▲ Tel: 408.263.3214 ▲ CM1402 VALUE 0.275mm Round Non-Solder Mask defined pads 0.325mm Round 0.125 - 0.150mm 0.330mm Round 50/50 by volume No Clean OSP (Entek Cu Plus 106A) +50µm +20µm 60 seconds 260° ...
Page 8
... CSP Mechanical Specifications CM1402 devices are packaged in a custom Chip Scale Package (CSP). Dimensions are presented below. For complete information on CSP packaging, see the Cali- fornia Micro Devices CSP Package Information docu- ment. PACKAGE DIMENSIONS Package Custom CSP Bumps Millimeters Dim ...