APL1431 Anpec Electronics Corporation, APL1431 Datasheet
APL1431
Available stocks
Related parts for APL1431
APL1431 Summary of contents
Page 1
... Output voltage may be set to any value between V two external resistors (see Figure 2). When used with an photocoupler, the APL1431 is an ideal volt- age reference in isolated feedback circuits for 2.5V to 12V switching-mode power supplies. This device = V to 20V has a typical output impedance of 0 ...
Page 2
... tic & Parameter SOT-23 SOT-89 TO-92 APL1431XXC APL1431XXI APL1431XXC APL1431XXI (Soldering, 10sec 25°C ( unless otherwise noted) A Test Conditions APL431A 2.487 REF ...
Page 3
... Figure 3. Test Circuit for REF Application schematic REF 1 R should provide cathode current large than b 1mA to maintain APL431 work properly. 3 APL1431 Min. Typ. Max. 1 0.25 0.5 0.1 1 0.1 0.4 *1 100 K(off) K(off) 5-Volt Precision Regulator ...
Page 4
... APL1431 Typical Characteristics Reference Current vs.Temperature 125 100 75 50 -40 - Temperature - C Cathode Current vs. Cathode Voltage 100 50 0 -50 -100 - Cathode Voltage -V Copyright ANPEC Electronics Corp. Rev. A.3 - May., 2003 Cathode Current vs. Cathode Voltage 800 600 400 200 0 -200 60 80 100 -1 Reference Voltage vs. Temperature 2 ...
Page 5
... APL1431 Typical Characteristics (Cont.) Small-Signal Voltage Amplification vs Frequency Frequency - kHz Off-State Cathode Current vsTemperature 0 20V REF 0.4 0.3 0.2 0.1 0 -40 - Temperature ( C) Copyright ANPEC Electronics Corp. Rev. A.3 - May., 2003 100 1000 -0.25 -0.5 -0.75 -1.25 -1.5 -1. 100 5 Pulse Response 6 Input 5 4 output ...
Page 6
... APL1431 Typical Characteristics (Cont.) Off-State Cathode Current vs Cathode Voltage 2500 V =0 REF 2000 1500 1000 500 0 -500 - Cathode Voltage (V) Figure 9 Stability Boundary Conditions 100 REF =3. 0.001 0.01 Load Capacitance - F Figure 11 Copyright ANPEC Electronics Corp. ...
Page 7
... APL1431 Packaging Information SOT- Dim M in Copyright ANPEC Electronics Corp. Rev. A.3 - May., 2003 illim ax ...
Page 8
... APL1431 Packaging Information SOT- in. A 1. 0.35 C 0. 2.29 H 3.75 L 0.80 Copyright ANPEC Electronics Corp. Rev. A.3 - May., 2003 illim eters M ax. 1.60 0.56 0.48 0.44 4.60 1. 2.60 4.25 1. Inches M in. M ax. 0.055 0.063 0.016 0.022 0.014 ...
Page 9
... APL1431 Packaging Information TO- SEATING PLANE Copyright ANPEC Electronics Corp. ...
Page 10
... APL1431 Physical Specifications Terminal Material Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb) Lead Solderability Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition (IR/Convection or VPR Reflow) Reference JEDEC Standard J-STD-020A APRIL 1999 Pre-heat temperature Classification Reflow Profiles Average ramp-up rate(183 C to Peak) Preheat temperature 125 ± Temperature maintained above 183 C Time within actual peak temperature 10 – ...
Page 11
... APL1431 R e lia b ilit ite ...
Page 12
... APL1431 Carrier Tape & Reel Dimensions Application 3.18~12 4.0±0 TO-92 27.0 MAX 20.0 MAX 11.0 MAX T2 W 0.36~0.68 17.5~19 Cover Tape Dimensions Application Carrier Width SOT- 23 SOT- 89 TO-92 Copyright ANPEC Electronics Corp. Rev. A.3 - May., 2003 H2A F1F2 F1,F2 2.5+0.2 0.36~0.53 9.0 MAX -0 2.5 MIN 12.7± ...