FCBP110LD1L03

Manufacturer Part NumberFCBP110LD1L03
DescriptionF I N I S A R Preliminary Product Specification 10gb/s Laserwire? Serial Data Link Active Cable
ManufacturerFinisar Corporation.
FCBP110LD1L03 datasheet
 


1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
Page 1/8

Download datasheet (190Kb)Embed
Next
F i n i s a r
PRELIMINARY Product Specification
10Gb/s Laserwire™ Serial Data Link Active Cable
PRODUCT FEATURES
• Single 1.0 – 10.3125 Gb/s
bi-directional link.
• RoHS-6 compliant (lead-free)
• Available in lengths of
3, 5, 10 and 30m
• Metal enclosure for low EMI
• Single 3.3V power supply
• Low power dissipation:
<500mW typical per end
• Operating temperature range:
0°C to 60°C
• RJ-45 width
• Red/Green LED link indicators
Finisar’s Laserwire™ active cables provide the lowest-cost serial data link solution for up
to 10 Gb/s, while providing a very lightweight, low-EMI and low-power alternative to
comparable copper solutions. Laserwire™ operates independently of protocol and can
thus be used in a wide range of applications. Laserwire™ plugs into the Laserwire™
Jack (P/N FCBJ110LE1), a small-footprint host-board connector. In addition, connection
to SFP+ or XFP ports is possible using Laserwire™ XFP or SFP+ adapters (P/N
FTLX0011D4BNL or FTLX0071D4BNL, respectively). Laserwire™ utilizes a limiting
receiver, avoiding the challenges of a linear receiver interface.
PRODUCT SELECTION
FCBP110LD1L03
FCBP110LD1L05
FCBP110LD1L10
FCBP110LD1L20
FCBP110LD1L30
© Finisar Corporation December 2009 Rev. A6 Preliminary
FCBP110LD1Lxx
APPLICATIONS
• 1/10 Gigabit Ethernet
• 1/2/4/8G Fibre Channel
• InfiniBand x1
• High Performance Computing
Interconnects
• SATA/SAS
• HDMI
• PCI-e x1
3-meter cable
5-meter cable
10-meter cable
20-meter cable
30-meter cable
Page 1

FCBP110LD1L03 Summary of contents

  • Page 1

    ... Jack (P/N FCBJ110LE1), a small-footprint host-board connector. In addition, connection to SFP+ or XFP ports is possible using Laserwire™ XFP or SFP+ adapters (P/N FTLX0011D4BNL or FTLX0071D4BNL, respectively). Laserwire™ utilizes a limiting receiver, avoiding the challenges of a linear receiver interface. PRODUCT SELECTION FCBP110LD1L03 FCBP110LD1L05 FCBP110LD1L10 FCBP110LD1L20 FCBP110LD1L30 © Finisar Corporation December 2009 Rev. A6 Preliminary ...

  • Page 2

    Pin Descriptions Pin Symbol 1 V Ground EE 2 TX- Transmitter Inverted DATA in 3 TX+ Transmitter Non-Inverted DATA Ground Power Supply (+3.3V ± 5%) CC ...

  • Page 3

    III. Electrical Characteristics Parameter Supply Voltage Supply Current Link Turn-On Time Transmit Turn-On Time Transmitter Differential data input swing Receiver Differential data output swing Power Supply Ripple Tolerance Notes: 1. From power-on and ...

  • Page 4

    IV. High Speed Electrical Characteristics Parameter – Transmitter Inputs Reference Differential Input Impedance Termination Mismatch DC Common mode Voltage Input AC Common Mode Voltage Differential Input Return Loss Differential to Common Mode Loss ...

  • Page 5

    Parameter – Receiver Outputs Reference Differential Output Impedance Termination Mismatch DC Common mode Voltage Output AC Common Mode Voltage Output Rise and Fall time (20% to 80%) Differential Output Return Loss Common Mode ...

  • Page 6

    -10 -15 0 Figure 4. Maximum Transmitter Input and Receiver Output Differential Return Loss V. General Specifications Data Rate Specifications Bit Rate Bit Error Ratio Notes: 1. 1/10 Gigabit Ethernet and ...

  • Page 7

    VIII. Mechanical Specifications Insertion, Extraction and Retention Forces Cable Tensile Load (Short Term) Cable Tensile Load (Long Term) Crush Resistance Impact Resistance Flexing Twist Bend Cable to Host Connector Retention Force Host Connector ...

  • Page 8

    IX. Application Note of Recommended Host-Board Connections. Figure 6. Recommended host board configuration showing power supply filtering, required AC-coupling capacitors, and status pull-up resistors. X. References 1. SFF-8077i rev 4.5 – XFP Specifications, ...