LICAL-TRC-MT001 Linx Technologies, Inc., LICAL-TRC-MT001 Datasheet
LICAL-TRC-MT001
Related parts for LICAL-TRC-MT001
LICAL-TRC-MT001 Summary of contents
Page 1
... Definable recognition authority Paging Transmitter ID output Custom data transfer ORDERING INFORMATION Device targeting PART # Wide 2.0 to 5.5V operating voltage LICAL-TRC-MT Low supply current (370µA @ 3V) MDEV-LICAL-MT True serial encoding MT transcoders are shipped in reels of 1,600 Selectable baud rates No programming required 0.309 (7.85) 0.207 (5.25) 0.284 (7.20) 0.030 (0 ...
Page 2
ELECTRICAL SPECIFICATIONS Parameter Designation Min. POWER SUPPLY Operating Voltage V 2.0 CC Supply Current 2.0V V – 3.0V V – 5.0V V – CC Power-Down Current: I PDN At 2.0V V – CC ...
Page 3
... PIN ASSIGNMENTS 1 LICAL-TRC-MT VCC CRT/LRN 5 ENC_SEL 6 SER_IO SEL_BAUD 7 CONFIRM MODE_IND 8 TR_PDN 9 TR_SEL 10 TR_DATA Figure 4: MT Series Transcoder Pin Assignments Pin Name Pin Number I — CC D0- 11-13, 17-19 I/O CRT/LRN 4 I Create / Learn Mode Activation Line ENC_SEL 5 I SER_IO 6 I/O CONFIRM 7 O Transmission Confirmation Line ...
Page 4
OVERVIEW Many products and applications call for the transfer of button presses or switch closures across a wireless link. Traditionally, a remote control link has operated in only one direction, from a transmitter to a receiver. The cost associated with ...
Page 5
TRANSCODER OPERATION When the transcoder powers on for the first time default set-up. When in this mode, the transcoder looks at the state of the ENC_SEL line on power- up. If the line is high, then ...
Page 6
CREATE MODE Create Mode allows the generation of a unique address to ensure the uniqueness of a transmission and prevent unintentional operation of devices. The MT Series transcoder allows for the creation of 16,777,216 (2 addresses. The assignment of the ...
Page 7
LATCH MODE The transcoder has two output options based on the state of the LATCH line. If the line is low, then all of the status line outputs will be momentary, meaning that they will only be high for as ...
Page 8
SERIAL OUTPUT Upon reception of every valid packet, the transcoder outputs a serial data stream containing information about the transmission. The information takes two forms depending on the User Access setting. If the User Access is set to open, then ...
Page 9
... VCC GND NC MAX4544 1 20 VCC GND CRT/LRN ENC_SEL LATCH 6 15 SER_IO SEL_BAUD 7 14 CONFIRM MODE_IND 8 13 TR_PDN TR_SEL TR_DATA D0 LICAL-TRC-MT Page 17 ...
Page 10
Page 18 Page 19 ...
Page 11
Page 20 Page 21 ...
Page 12
TRANSCODER MODE_IND DEFINITIONS The MODE_IND line is the primary means of indicating the state of the transcoder to the user. The table below gives the definitions of the MODE_IND signals. ON for as long as the transcoder is receiving data ...
Page 13
Config Mode Is the SER_IO Yes line high the Yes ENC_SEL line high? Randomize the No Start Erase timer CRT/LRN line Is the No CRT/LRN line high? Write the new address to memory Yes Did the Yes Timeout ...
Page 14
... TYPICAL APPLICATIONS The MT Series transcoder is ideal for replicating button presses for remote control applications. An example application circuit is shown below. VCC VCC 1 LICAL-TRC-MT VCC 2 D6 10k 2.2k 3 100k D7 4 CRT/LRN VCC 5 ENC_SEL VCC 100k 6 SER_IO SEL_BAUD To Processor CONFIRM MODE_IND 8 TR_PDN To Transceiver 9 TR_SEL ...
Page 15
... Under no circumstances shall any user be conveyed any license or right to the use or ownership of such items. © 2008 by Linx Technologies, Inc. The stylized Linx logo, Linx, “Wireless Made Simple”, CipherLinx, and the stylized CL logo are the trademarks of Linx Technologies, Inc. ...