NTQ160

Manufacturer Part NumberNTQ160
DescriptionAc/dc Power Supply Quad-out 3.3v/5v/12v/12v 15a/10a/2a/2a 50w
ManufacturerETC-unknow
NTQ160 datasheet
 


1
Page 1
2
Page 2
3
Page 3
Page 1/3

Download datasheet (147Kb)Embed
Next
50-165 Watts
NTQ160 Series
Special Features
• Active power factor correction
• EN61000-3-2 compliance
• Remote sense on outputs
one and two
• Power fail and remote inhibit
• 5V Standby output
• DC Power good
• Single wire current sharing on
outputs one and two
• Wide range adjustable on outputs 1 & 2
• Built-in Class B EMI filter
• Overvoltage protection
• Overload protection
• Thermal overload protection
• Outputs 3 & 4 are floating
Environmental
Operating temperature: 0° to 50°C ambient; derate
each output at 2.5% per degree from
50° to 70°C
Electromagnetic susceptibility: Designed to meet
EN61000-4, -2, -3, -4, -5, -6, -8, -11 Level 3
Humidity: Operating; non-condensing
10% to 95%
Vibration: Three orthogonal axes, sweep at
1 oct/min, 5 min. dwell at four major resonances 0.7
G peak 5 Hz to 500 Hz, operational
Storage temperature: -40° to 85°C
Temperature coefficient: ± .04% per °C
MTBF demonstrated: >1 million hours at full load and
25°C ambient conditions
Americas: (760) 930-4600
116
Total Power:
Input Voltage: 85-264 VAC
# of Outputs:
Electrical Specs
Input
Input range
Frequency
Inrush current
Efficiency
EMI filter
Power factor
Safety ground leakage
current
Output
Maximum power
Adjustment range
Hold-up time
Overload protection
Overvoltage protection
Standby output
Logic Control
Power failure
Remote Inhibit
Remote sense
DC O
VDE
UL
CSA
NEMKO
BABT
CB
CE
Support: (888) 41-ASTEC or (407) 241-2752
Europe (UK) 44 (1384) 842-211
50-165 Watts
Quad
85-264 VAC
47-63 Hz
38 A max., cold start @ 25°C
65% typical at full load @ 115 VAC
input
FCC Class B conducted and radiated,
CISPR 22 Class B conducted and
radiated, EN55022 Class B conducted
and radiated, VDE 0878 PT3 Class B
conducted and radiated.
0.99 typical
<1 mA @ 50/60 Hz, 264 VAC input
50W convection, 165 W with 30 CFM
forced air
1.8V - 3.5V; 3.0V - 5.5V on outputs
one and two
20 ms @ 165 W load
Short circuit protection on all outputs.
Case overload protected @ 110-145%
above peak rating. Latching type
recycle AC to reset.
Tracks outputs 1 & 2: 20% to 35%
above output setting
5V@ 2 A regulated ±5%
TTL logic signal goes high 100-500
msec after V1 output; it goes low at
least 4 msec before loss of regulation
Requires contact closure to inhibit
outputs
Compensates for 0.5 V lead drop
minimum, will operate without
remote sense connected. Reverse
connection protection.
TTL logic signal goes high after main
output is in regulation. It goes low
when there is a loss of regulation.
Safety
0805/EN60950 (IEC950)
21310-3336-0021
(129066)
UL1950
E186249
CSA 22.2-234 Level 3
LR109492C
EN 60950/EMKO-TUE
P00100493
(74-sec) 203
EN60950/EN41003
650251, NC/00069
Certificate and report
9661, 9662, 8788
Mark (LVD)
Asia (HK) 852-2437-9662
rev 04.29.04

NTQ160 Summary of contents

  • Page 1

    ... Watts NTQ160 Series Special Features • Active power factor correction • EN61000-3-2 compliance • Remote sense on outputs one and two • Power fail and remote inhibit • 5V Standby output • DC Power good • Single wire current sharing on outputs one and two • ...

  • Page 2

    Ordering Information Model Output Minimum Number Voltage Load NTQ162 +3.3 V(1.8 - 3.5V 5.5V NTQ163 + 5.5V +3.3 V ...

  • Page 3

    VR1 VR2 D27 HTSK-SEC3 D24 L15 IC8 IC7 R67 C84 C86 SK6 R87 C43 C46 C47 1 10 C72 THR3 C29 C41 C42 L9 THR2 SEC_DB R41 C37 C36 Z4 ...