NS2B095AT

Manufacturer Part NumberNS2B095AT
DescriptionSpecifications For Nichia Chip Type Blue Led
ManufacturerNICHIA CORPORATION
NS2B095AT datasheet
 


1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
17
Page 1/17

Download datasheet (619Kb)Embed
Next
Nichia STS-DA1-0177C
<Cat.No.090428>
SPECIFICATIONS FOR NICHIA CHIP TYPE BLUE LED
NS2B095AT
MODEL :
NICHIA CORPORATION

NS2B095AT Summary of contents

  • Page 1

    ... SPECIFICATIONS FOR NICHIA CHIP TYPE BLUE LED MODEL : NICHIA CORPORATION NS2B095AT Nichia STS-DA1-0177C <Cat.No.090428> ...

  • Page 2

    Absolute Maximum Ratings Item Forward Current Pulse Forward Current Allowable Reverse Current Power Dissipation Operating Temperature Storage Temperature Dice Temperature Soldering Temperature I Conditions : Pulse Width ≤ 10msec. and Duty ≤ 1/10 FP (2) Initial Electrical/Optical Characteristics ...

  • Page 3

    DIMENSIONS AND MATERIALS Please refer to “OUTLINE DIMENSIONS” on the following page. Material as follows ; Package Encapsulating Resin Electrodes 4.PACKAGING · The LEDs are packed in cardboard boxes after taping. Please refer to “TAPING DIMENSIONS” and “PACKING ”on ...

  • Page 4

    TEST ITEMS AND RESULTS Standard Test Item Test Method Resistance to JEITA ED-4701 Soldering Heat (Reflow Soldering) Solderability JEITA ED-4701 (Reflow Soldering) Temperature Cycle JEITA ED-4701 Moisture Resistance Cyclic JEITA ED-4701 High Temperature Storage JEITA ED-4701 Temperature Humidity ...

  • Page 5

    Moisture Proof Package · When moisture is absorbed into the SMT package it may vaporize and expand during soldering. There is a possibility that this can cause exfoliation of the contacts and damage the optical characteristics of the ...

  • Page 6

    Static Electricity · Static electricity or surge voltage damages the LEDs recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. · All devices, equipment and machinery must be properly grounded. It ...

  • Page 7

    Warpage of circuit board with soldered LEDs may result in damage or package breakage of the LEDs. Please pay special attention to the orientation of the LEDs as to avoid LED failure caused by bow, twist and warpage of ...

  • Page 8

    Handling Precautions · Bare Hand When handling the product, touching encapsulant with bare hands will contaminate its surface that could affects on optical characteristics. force to the encapsulant by hands might result in catastrophic failure of the LEDs due ...

  • Page 9

    Printed Circuit Board Assembled (PCB with LEDs soldered) Do not stack assembled PCBs together. Since silicone is a soft material, abrasion between two PCB assembled with silicone encapsulated LED might cause catastrophic failure of the LEDs due to damage ...

  • Page 10

    Soldering Conditions · The LEDs can be soldered in place using the reflow soldering method. guarantee on the LEDs after they have been assembled using the dip soldering method. · Recommended soldering conditions Reflow Soldering Lead Solder Pre-heat 120 ...

  • Page 11

    Cleaning · recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Freon solvents should ...

  • Page 12

    W 470 460 0 0 0.1 0.2 Color coordinates Measurement allowance is ± 0.01. ICI Chromaticity Diagram 550 560 570 580 0.3 0.4 0.5 ...

  • Page 13

    ... Ambient Temperature vs. Allowable Forward Current 250 I =60mA FP 200 150 100 Rja=120°C 100 0 30 Ambient Temperature Ta (°C ) NICHIA CORPORATION Ta=25° 100 Solder Temperature (Cathode Side) vs. Allowable Forward Current 250 200 150 (76,120) (85,101) 100 120 0 ...

  • Page 14

    ... Forward Current I (mA) FP Ta=25°C I =60mA F 450 550 650 Wavelength λ (nm) Directivity 1.0 =60mA FP 0 100 90° 60° Radiation Angle NICHIA CORPORATION Y 0° 10° 20° 30° 40° Y 50° 60° 70° Ta=25°C I =60mA FP 80° X-X Y-Y 90° 30° 0° 0.5 1.0 Model ...

  • Page 15

    ... Cathode mark ITEM PACKAGE ENCAPSULATING RESIN Silicone Resin (with Diffused ) ELECTRODES NS2B095A has a protection device built protection circuit against static electricity. 0.15 Anode MATERIALS Ceramics Ag Plating NICHIA CORPORATION 2.8 0.8 Cathode A K Protection device NS2B095A Model Title OUTLINE DIMENSIONS 081127814552 No. Unit mm 10/1 Scale Allow ...

  • Page 16

    ... Label 1.35 φ 1 XXXX LED +0 TYPE NS2x095AT LOT xxxxxx- QTY pcs RoHS ±0.1 LEDs mounting part NICHIA CORPORATION ±1 11.4 φ 180 +0 ±0 LEDs Embossed carrier tape Reel Lead Min.100mm (No LEDs) Reel Lead Min.400mm NS2x095AT Model Title TAPING DIMENSIONS 081121815082 No ...

  • Page 17

    ... OKA, KAMINAKA, ANAN, TOKUSHIMA, The box is partitioned with the cardboard. Label XXXX LED TYPE NS2x095AT RANK RoHS QTY PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Quantity/box (pcs) 21,000 MAX. 45,000 MAX. 90,000 MAX. NS2x095AT PACKING 070905770511 ...