LT1037 Linear Technology Corporation, LT1037 Datasheet - Page 4

• Manufacturer Part Number: LT1037
• Description: Low Noise, High Speed Precision Operational Amplifiers
• Manufacturer: Linear Technology Corporation

LT1007/LT1037
ELECTRICAL CHARACTERISTICS
The
SYMBOL
V
I
I
CMRR
PSRR
A
V
P
The
SYMBOL
V
I
I
CMRR
PSRR
A
V
P
For MIL-STD components, please refer to LTC 883C data sheet for test
listing and parameters.
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: Input Offset Voltage measurements are performed by automatic
test equipment approximately 0.5 seconds after application of power. AM
and AC grades are guaranteed fully warmed up.
Note 3: Long Term Input Offset Voltage Stability refers to the average
trend line of Offset Voltage vs Time over extended periods after the first 30
days of operation. Excluding the initial hour of operation, changes in V
during the first 30 days are typically 2.5 V. Refer to typical performance
curve.
Note 4: This parameter is tested on a sample basis only.
4
OS
B
OS
B
OS
VOL
OUT
D
OS
VOL
OUT
D
Temp
Temp
V
V
OS
OS
denotes the specifications which apply over the temperature range – 40 C T
denotes the specifications which apply over the temperature range – 55 C T
PARAMETER
Input Offset Voltage
Average Input Offset Drift
Input Offset Current
Input Bias Current
Input Voltage Range
Common Mode Rejection Ratio
Power Supply Rejection Ratio
Large-Signal Voltage Gain
Maximum Output Voltage Swing
Power Dissipation
PARAMETER
Input Offset Voltage
Average Input Offset Drift
Input Offset Current
Input Bias Current
Input Voltage Range
Common Mode Rejection Ratio
Power Supply Rejection Ratio
Large-Signal Voltage Gain
Maximum Output Voltage Swing
Power Dissipation
CONDITIONS
(Note 2)
(Note 10)
V
V
R
R
R
CM
S
L
L
L
= 4.5V to 18V
= 10.3V
2k, V
1k, V
2k
CONDITIONS
(Note 2)
(Note 10)
V
V
R
R
R
CM
S
L
L
L
= 4.5V to 18V
O
O
= 10.5V
= 10V
= 10V
2k, V
1k, V
2k
OS
O
O
= 10V
= 10V
Note 5: 10Hz noise voltage density is sample tested on every lot. Devices
100% tested at 10Hz are available on request.
Note 6: See the test circuit and frequency response curve for 0.1Hz to
10Hz tester in the Applications Information section.
Note 7: See the test circuit for current noise measurement in the
Applications Information section.
Note 8: This parameter is guaranteed by design and is not tested.
Note 9: The inputs are protected by back-to-back diodes. Current limiting
resistors are not used in order to achieve low noise. If differential input
voltage exceeds 0.7V, the input current should be limited to 25mA.
Note 10: The Average Input Offset Drift performance is within the
specifications unnulled or when nulled with a pot having a range of 8k to
20k .
LT1007AM/LT1037AM
MIN
112
104
3.0
2.0
10.3
12.5
A
A
14.0
10.0
TYP
126
126
100
0.2
25
15
11.5
13.5
85 C, V
125 C, V
20
MAX
150
0.6
S
60
50
60
S
= 15V, unless otherwise noted.
= 15V, unless otherwise noted.
MIN
MIN
105
101
104
100
2.0
1.5
2.0
1.5
12.0
10.3
12.0
LT1007M/LT1037M
10
LT1007I/LT1037I
15.0
12.0
14.0
10.0
TYP
TYP
120
120
120
120
100
0.3
0.3
11.7
13.6
11.5
13.5
40
20
95
50
20
25
35
MAX
MAX
170
125
165
160
1.0
1.0
80
85
90
95
sn100737 100737fbs
UNITS
UNITS
V/ V
V/ V
V/ V
V/ V
V/ C
V/ C
mW
mW
nA
nA
dB
dB
nA
nA
dB
dB
V
V
V
V
V
V