160S321B1 Pacer Components, 160S321B1 Datasheet
160S321B1
Related parts for 160S321B1
160S321B1 Summary of contents
Page 1
... Rev. 3.0 Nov. 28, 2005 * Changed of Document Format Issued by Checked by Approved by 160S321B1(Rev. 3.0) Description × dot font table”(39Hex) × dot font table”(39Hex) Page Rev. 3.0 Model No.: 160S321B1 Note All pages Page 11 Page 15 Page 15 All pages Customer’s Approval ...
Page 2
... Select Font Mode (F6H + n, RW=0, RS=0)....................................................................... Page 10 6.2 Jumper Setting.............................................................................................................................. Page 11 6.3 Display Examples......................................................................................................................... Page 11 6.3.1 Serial Control....................................................................................................................... Page 11 6.3.2 Extended Graphic Commands ............................................................................................. Page 11 6.3.3 Displaying Graphics ............................................................................................................ Page 12 * Appendix 1: Characters Font Table1 (CG_ROM, 6×8dot font).....................................................Page 13 * Appendix 2: Characters Font Table2 (CG_ROM, 11×16dot font) .................................................Page 14 160S321B1(Rev. 3.0) ~~~~~~~~~~~~~~~~ Index ~~~~~~~~~~~~~~~~ Page ...
Page 3
... Graphic Display Module 1. SCOPE This specification applies to VFD module (Model No. 160S321B1) manufactured by SSVD (Shanghai Samsung Vacuum Devices). 2. FEATURES × * 160 3 2 dot graphic bit parallel M68 LCD compatible & asynchronous serial interface (9600, 19200 bps). * Since a DC/DC converter is used, only +5V * CG-ROM which is mounted on module offers brightness levels can be selected by brightness control command ...
Page 4
... Low Level Input Current Brightness Display Color ( * ) : 160S321B1(Rev. 3.0) Symbols ...
Page 5
... Graphic Display Module 4.7 Timing Chart 4.7.1 Parallel interface write-in timing R DB0~7 4.7.2 Parallel interface read-out timing R usy If the Busy signal is Low send data enable. 160S321B1(Rev. 3.0) Min 30ns Min Min 230ns 230ns Min Min 500ns Min 80ns VALID Min Min 230ns 30ns ...
Page 6
... GND /RST 4 5 SBUSY 4.8.2 Parallel interface connector Pin No. Signal Name 1 GND 2 VCC 3 PBUSY R 160S321B1(Rev. 3. /Baud-rate [us] Description Power Supply Receive Data Power and Signal Ground Reset Display Busy Description Pin No. Ground 8 Power Supply 9 Display Busy 10 Select ...
Page 7
... Graphic Display Module 4.9 System Block Diagram RXD PBUSY /RST DATA BUFFER SBUSY V CC GND 4.10 Outer Dimensions 160S321B1(Rev. 3.0) 8-bit MCU DC/DC Converter Fig.-2 System Block Diagram Fig.-3 Outer Dimensions Page 160 × × × × DOT CIG VFD VH F1 ...
Page 8
... This display is organized as 160 (MSB) uppermost. 5.3 Graphical Data Writes 160S321B1(Rev. 3. dot – Max characters × × dot – Max characters × × dot – Customer font × ...
Page 9
... If this bit is set to ‘0’ the VFD’s power supply is turned off to reduce power consumption. RS R/W Bit7 6.1.6 Display Shift Left (18H, RS=0) Shift the display left, one character position. 6.1.7 Display Shift Right (1CH, RS=0) Shift the display right, one character position. 160S321B1(Rev. 3.0) Bit6 Bit5 Bit4 Bit3 Bit6 Bit5 ...
Page 10
... Additional Serial Data Command: Set RS Low (0FH) Set the RS line low for the following byte only. Used in serial communications only. 6.1.12 Select Font Mode (F6H + n, RW=0, RS= × 8 dot character (default × 1 6dot character. 160S321B1(Rev. 3.0) Bit6 Bit5 Bit4 Bit3 2nd Column 3rd Column ...
Page 11
... Written data may require additional busy times. Text data is not written into the DD RAM and therefore can not be read back. Graphical text can not be shifted onto the display. The graphics mode is disabled as soon as any valid LCD command is received. 160S321B1(Rev. 3.0) J3 Setting Value × ...
Page 12
... The following example displays a simple graphical image. Command bytes that are underlined should be sent with RS line low. Area Co-ordinates Area Command X1 F5H 50H 01H F5H 50H 01H Graphic Data Map (Horizontal) 160S321B1(Rev. 3. 50H Display Mode 63H 02H ‘H’ 63H 02H ‘ ...
Page 13
... Graphic Display Module * Appendix 1: Characters Font Table1 (CG_ROM, 6×8dot font) 160S321B1(Rev. 3.0) Page ...
Page 14
... Graphic Display Module * Appendix 2: Characters Font Table2 (CG_ROM, 11×16dot font) 160S321B1(Rev. 3.0) Page ...