MAX8588 Maxim Integrated Products, MAX8588 Datasheet - Page 2

• Manufacturer Part Number: MAX8588
• Description: High-Efficiency Low-IQ PMIC
• Manufacturer: Maxim Integrated Products

ABSOLUTE MAXIMUM RATINGS
IN, IN45, IN6, MR, LBO, DBO, RSO, POK, SCL, SDA,
REF, CC_, ON_, FB_, DBI, LBI, V1, V2, RAMP, BYP,
PV1, PV2, PV3, SLPIN to IN...................................-0.3V to +0.3V
V4, V5 to GND ..........................................-0.3V to (V
V6 to GND ..................................................-0.3V to (V
PV1 to PG1 ............................................................-0.3V to +6.0V
PV2 to PG2 ............................................................-0.3V to +6.0V
PV3 to PG3 ............................................................-0.3V to +6.0V
LX1 Continuous Current....................................-1.30A to +1.30A
High-Efficiency, Low-I
Dynamic Core for PDAs and Smartphones
ELECTRICAL CHARACTERISTICS
(V
are at T
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
2
PV1, PV2, PV3, SLPIN, IN Supply
Voltage Range
IN45, IN6 Supply Voltage Range
IN Undervoltage-Lockout (UVLO)
Threshold
Quiescent Current
BKBT Input Current
REF Output Voltage
SYNCHRONOUS-BUCK PWM REG1
REG1 Voltage Accuracy
FB1 Voltage Accuracy
FB1 Input Current
Error-Amplifier Transconductance
Dropout Voltage (Note 1)
IN
BKBT, V7, SLP, SRAD, PWM3 to GND...............-0.3V to +6V
MR to GND ...........................................-0.3V to (V
_______________________________________________________________________________________
= 3.6V, V
A
= +25°C.)
PARAMETER
BKBT
= 3.0V, V
LBI
= 1.1V, V
PV1, PV2, PV3, IN, and SLPIN must connect together
externally
V
V
No load (I
I
I
I
ON1 = 0
ON1 = IN
0 to 10µA load
FB1 = GND, 3.6V ≤ V
FB1 used with external resistors, 3.6V ≤ V
load = 0 to 1300mA
FB1 used with external resistors
Referred to FB
Load = 800mA
Load = 1300mA
PV2
SLPIN
IN6
IN
IN
DBI
)
rising
falling
+ I
= 1.35V, circuit of Figure 5, T
+ I
PV3
IN45
PV1
IN45
+ I
IN6
IN
+
+
IN
+ 0.3V)
+ 0.3V)
+ 0.3V)
+
Q
PV1
Only V7 on, V
REG1 and REG2 on in switch mode,
REG3 off
REG1 and REG2 on in sleep mode,
REG3 off
All REGs on
CONDITIONS
≤ 5.5V, load = 0 to 1300mA
PMIC with
LX2 Continuous Current........................................-0.9A to +0.9A
LX3 Continuous Current........................................-0.5A to +0.5A
PG1, PG2, PG3 to GND.........................................-0.3V to +0.3V
V1, V2, V4, V5, V6 Output Short-Circuit Duration.......Continuous
Continuous Power Dissipation (T
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
6mm x 6mm 48-Pin Thin QFN
(derate 26.3mW/°C above +70°C) ...........................2105mW
IN
A
= 0°C to +85°C, unless otherwise noted. Typical values
= 3.0V
PV1
≤ 5.5V,
1.2375
2.200
1.231
2.25
3.25
MIN
A
2.6
2.4
= +70°C)
www.DataSheet4U.com
TYP
2.40
2.35
1.25
1.25
130
225
180
293
0.8
3.3
32
60
87
4
1.2625
2.525
1.269
MAX
2.55
3.35
100
280
450
5.5
5.5
UNITS
mV
µA
µA
nA
µS
V
V
V
V
V
V