A2106AA3

Manufacturer Part NumberA2106AA3
DescriptionTeccor® Balanced Three-chip Sidactor Device ;; Package= TO-220 Modified
ManufacturerTeccor Electronics
A2106AA3 datasheet
 


1
Page 1
2
Page 2
Page 1/2

Download datasheet (119Kb)Embed
Next
Balanced Three-chip SIDACtor Device
Balanced Three-chip SIDACtor Device
The three-chip modified TO-220 SIDACtor balanced solid state device is designed for
1
3
telecommunication protection systems that reference Tip and Ring to earth ground.
Applications include any piece of transmission equipment that requires balanced protection.
This device is built using Teccor’s patented “Y” (US Patent 4,905,119) configuration.
2
The SIDACtor device is used to enable equipment to meet various regulatory requirements
including GR 1089, ITU K.20,K.21 and K.45, IEC 60950, UL 60950, and TIA-968 (formerly
known as FCC Part 68).
Electrical Parameters
V
V
DRM
S
Volts
Volts
Part
Number *
Pins 1-2, 2-3
P1553A_
130
180
P1803A_
150
210
P2103A_
170
250
P2353A_
200
270
P2703A_
230
300
P3203A_
270
350
P3403A_
300
400
P5103A_
420
600
A2106A_3 **
170
250
A5030A_3 **
400
550
* For individual “AA”, “AB”, and “AC” surge ratings, see table below.
** Asymmetrical
General Notes:
• All measurements are made at an ambient temperature of 25 °C. I
• I
is a repetitive surge rating and is guaranteed for the life of the product.
PP
• Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities.
• V
is measured at I
DRM
DRM.
• V
is measured at 100 V/µs.
S
• Special voltage (V
and V
) and holding current (I
S
DRM
• Off-state capacitance is measured between Pins 1-2 and 3-2 at 1 MHz with a 2 V bias and is a typical value for “AA” product. “AB”
and “AC” capacitance is approximately 2x the listed value.
• Device is designed to meet balance requirements of GTS 8700 and GR 974.
Surge Ratings
I
I
PP
PP
2x10 µs
8x20 µs
Series
Amps
Amps
A
150
150
B
250
250
C
500
400
http://www.teccor.com
+1 972-580-7777
V
V
DRM
S
Volts
Volts
V
I
T
DRM
Pins 1-3
Volts
µAmps
130
180
8
5
150
210
8
5
170
250
8
5
200
270
8
5
230
300
8
5
270
350
8
5
300
400
8
5
420
600
8
5
50
80
8
5
270
340
8
5
applies to -40 °C through +85 °C temperature range.
PP
) requirements are available upon request.
H
I
I
PP
PP
10x160 µs
10x560 µs
10x1000 µs
Amps
Amps
90
50
150
100
200
150
2 - 34
SIDACtor
I
I
I
C
S
T
H
O
mAmps
Amps
mAmps
pF
800
2.2
150
40
800
2.2
150
40
800
2.2
150
40
800
2.2
150
40
800
2.2
150
30
800
2.2
150
30
800
2.2
150
30
800
2.2
150
30
800
2.2
120
40
800
2.2
150
30
I
I
PP
TSM
60 Hz
di/dt
Amps
Amps
Amps/µs
45
20
500
80
30
500
100
50
500
© 2003 Teccor Electronics
®
Data Book and Design Guide

A2106AA3 Summary of contents

  • Page 1

    ... TSM 60 Hz di/dt Amps Amps Amps/µ 500 80 30 500 100 50 500 © 2003 Teccor Electronics ® Data Book and Design Guide ...

  • Page 2

    ... Junction Temperature (T ) – ˚C J Normalized V Change versus Junction Temperature S © 2003 Teccor Electronics ® SIDACtor Data Book and Design Guide Balanced Three-chip SIDACtor Device Parameter Peak 100 Value Waveform = ...