ATSAM2193-G ATMEL Corporation, ATSAM2193-G Datasheet

no-image

ATSAM2193-G

Manufacturer Part Number
ATSAM2193-G
Description
Sound Synthesis
Manufacturer
ATMEL Corporation
Datasheet
Features
Description
The ATSAM2193 provides a single-chip, low-cost MIDI sound system. Equipped with
a serial and a parallel MIDI input, it provides state-of-the-art sound synthesis using a
full GM sound set together with a range of compatible effects. Its low power consump-
tion makes it ideal for all battery-powered applications such as portable Karaoke or
any other device using MIDI synthesis.
The ATSAM2193-G has the same functionality as the ATSAM2193 but is presented in
a TFBGA44 package.
Figure 1. Typical Hardware Configuration
Single-chip All-in-one Design, Only Requires External DAC
State-of-the-art Synthesis for Best Quality/Price Products
Synthesizer Chipset: ATSAM2193/ATSAM2193-G + DAC
Hardware Programmable DAC Mode
Typical Applications
TQFP44 (10 mm x 10 mm) Package for ATSAM2193
TFBGA44 (7 mm x 7 mm) Package for ATSAM2193-G
Low-power
– MIDI Control Processor, Serial and Parallel Interface
– Synthesis, General MIDI Wavetable Implementation
– Compatible Effects: Reverb + Chorus
– Spatial Effect
– 4-band Stereo Equalizer
– 38-voice Polyphony + Effects
– On-chip CleanWave
– I2S: 16 to 20 bits
– Japanese: 16 bits
– Battery-operated Musical Keyboards
– Portable Phones
– Karaokes
– Both Options Provide Small Footprint, Low Pin Count
– 95 mW Typical Operating, <5 µA Power-down
– 2.5V and 3.3V Power Supply or Single 2.5V Supply
– Built-in Power Switch
www.DataSheet4U.com
(Parallel MIDI)
MPU-401
MIDI IN
Wavetable Data, Firmware, RAM Delay Lines
ATSAM2193-G
ATSAM2193
or
Stereo
DAC
Audio
Out
Sound
Synthesis
ATSAM2193
ATSAM2193-G
Low-power
Single-chip
Synthesizer
with Effects
Rev. 2695A–DRMSD–06/03
1

Related parts for ATSAM2193-G

ATSAM2193-G Summary of contents

Page 1

... GM sound set together with a range of compatible effects. Its low power consump- tion makes it ideal for all battery-powered applications such as portable Karaoke or any other device using MIDI synthesis. The ATSAM2193-G has the same functionality as the ATSAM2193 but is presented in a TFBGA44 package. Figure 1. Typical Hardware Configuration ...

Page 2

... IN Miscellaneous Group X1 ATSAM2193/ATSAM2193-G 2 Function Digital ground - all pins should be connected to a ground plane. I/O power supply, 2.25V to 3.6V. All pins should be connected to a nominal 3.3V power. Core power supply, 2.25V to 2.75V. All pins should be connected to nominal 2.5V. If the built-in power switch is used for minimum power-down consumption, then all these pins should be connected to the output of the power switch PWROUT (pin 36) ...

Page 3

... VC3 21 11 GND 22 2695A–DRMSD–06/03 ATSAM2193/ATSAM2193-G Function Buffered X2 output, can be used to drive external DAC master clock (256 * Fs) PLL external RC network. Reset input, active low. This is a Schmitt trigger input, allowing direct connection network. Power switch output. Use this pin to supply 2.5V nominal core voltage by connecting it to all V pins ...

Page 4

... A6 IN Miscellaneous Group X1 ATSAM2193/ATSAM2193-G 4 Function Digital ground - all pins should be connected to a ground plane. I/O power supply, 2.25V to 3.6V. All pins should be connected to a nominal 3.3V power. Core power supply, 2.25V to 2.75V. All pins should be connected to nominal 2.5V. If the built-in power switch is used for minimum power-down consumption, then all these pins should be connected to the output of the power switch PWROUT (pin 36) ...

Page 5

... RUN A3 OUT Figure 2. Pinout by Pin Coordinate - 44-ball TFBGA (Top View) 2695A–DRMSD–06/03 ATSAM2193/ATSAM2193-G Function Buffered X2 output, can be used to drive external DAC master clock (256 * Fs) PLL external RC network. Reset input, active low. This is a Schmitt trigger input, allowing direct connection network ...

Page 6

... Low-level input voltage for X1, PDWN IL V High-level input voltage for X1, PDWN IH V Low-level output voltage High-level output voltage I OH Power consumption (crystal frequency =9.6 MHz) Power down supply current (using power switch) ATSAM2193/ATSAM2193-G 6 *NOTICE 2.5V ± 10 3.3V ± 10 -2mA OL = 2mA OH Stresses beyond those listed under “ ...

Page 7

... Chip select low to WR low CSLRWRL t WR high to CS high WRHCSH t WR pulse width PWR t Write data setup time DWS t Write data hold time DWH t Write cycle WRCYC ATSAM2193/ATSAM2193 PRD RDHCSH t t RDLDV DRH t WRCYC t t PWR WRHCSH t t DWS ...

Page 8

... DABD valid prior/after CLBD rising SOD t CLBD cycle time CLBD Figure 6. Digital Audio Frame Format WSBD (I2S) WSBD (Japanese) CLBD DABD MSB Notes: 1. Selection between I2S and Japanese format is via pin DACSEL. ATSAM2193/ATSAM2193 CLBD SOD SOD Min Typ 200 200 416 ...

Page 9

... PLL are stabilized. This takes about 20 ms. A typical RC/diode power-up network can be used. After RESET, the ATSAM2193 or ATSAM2193-G enters an initialization routine. It takes around 50 ms before a MIDI IN or MPU message can be processed. If PDWN is asserted low, then the crystal oscillator and PLL are stopped. The chip enters a deep power-down sleep mode ...

Page 10

... GND, VC3, VC2 Distribution and Decouplings All GND, VC3, VC2 pins should be connected. A GND plane is strongly recommended below the ATSAM2193 and ATSAM2193-G. The board GND + VC2 distribution should be in grid form. Recommended VC2 decoupling is 0.1 µF at each corner of the IC with an additional 10 µ ...

Page 11

... Recommended www.DataSheet4U.com Crystal Compensation and LFT Filter 2695A–DRMSD–06/03 Figure 9. ATSAM2193 X1 9.6 MHz GND GND Figure 10. ATSAM2193-G X1 9.6 MHz GND GND ATSAM2193/ATSAM2193 LFT R1 C2 470 Ohm ATSAM2193 10 nF GND LFT R1 C2 470 Ohm ...

Page 12

... Mechanical Dimensions www.DataSheet4U.com 44-lead TQFP Package ATSAM2193/ATSAM2193-G 12 Figure 11. Thin Plastic 44-lead Quad Flat Pack (TQFP44) Table 9. 44-lead TQFP Package Dimensions (in mm) Parameter Min A A1 0. 0.3 Nom Max 1.60 0.15 1.40 1.45 12.00 10.00 12.00 10.00 0.60 0.75 0.80 0.37 0.45 2695A–DRMSD–06/03 ...

Page 13

... TFBGA Package www.DataSheet4U.com Figure 12. 44-ball TFBGA Package Figure 13. Package Marking 2695A–DRMSD–06/03 F RANCE SAM2193-G YYWW 57541A XXXXXXXXX Note: A1 Ball in lower left-hand corner. ATSAM2193/ATSAM2193-G 0.80 0.35 0.26 0.53 13 ...

Page 14

... Fax: (81) 3-3523-7581 Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein ...

Related keywords