TDA1314 Philips Semiconductors, TDA1314 Datasheet
TDA1314
Related parts for TDA1314
TDA1314 Summary of contents
Page 1
... Stand-alone quadruple low noise DAC Car radio DAC in conjunction with DSP. GENERAL DESCRIPTION The TDA1314T is a quadruple very low noise high dynamic range DAC which is intended for use in motor cars and is controlled by the car radio DSP. Each channel incorporates an 8th-order IIR up-sampling filter from 1ASF to 4ASF followed by a 1st-order noise shaper and DAC ...
Page 2
... Philips Semiconductors Quadruple filter DAC BLOCK DIAGRAM August 1994 3 Product specification TDA1314T pagewidth full handbook, ...
Page 3
... PLL lock indicator August 1994 DESCRIPTION mode/scan input signal 1 in test mode as 2 S-bus = N 4f (45 N 128 operational amplifier supply voltage S-bus); scan input signal 2 in test mode 2 S-bus) 2 S-bus) signal as 4 Product specification TDA1314T ...
Page 4
... DAC. This mode is called the free running mode. If, in some applications, there is considerable jitter on the MCLK while WS is more stable (less jitter), the phase-locked mode should be selected. This mode is normally not used and is not recommended. 5 Product specification TDA1314T ...
Page 5
... V an external capacitor a soft switch-on of the DAC output currents is obtained. This pin can also be used as the analog mute input for all DAC output currents by pulling it to ground. 6 Product specification TDA1314T . A resistor connected to ref . Together with DDA ...
Page 6
... Philips Semiconductors Quadruple filter DAC August 1994 2 Fig.3 I S-bus timing and format. 7 Product specification TDA1314T ...
Page 7
... All voltages (pins 6, 7 and 15) referenced to ground. 2. Equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor. THERMAL CHARACTERISTICS SYMBOL R thermal resistance from junction to ambient in free air th j-a August 1994 CONDITIONS note 1 note 1 note 1 note 2 PARAMETER 8 Product specification TDA1314T MIN. MAX. UNIT ...
Page 8
... V 1 DDO maximum signal note 1; R > 0. maximum signal with respect to V 110 DDO with respect DDD DGND 9 Product specification TDA1314T TYP. MAX. UNIT 5.0 5.5 V 5.0 5.25 V 5.0 5. 145 mW V 0.2V V DDD ...
Page 9
... kHz; i A-weighted kHz; ripple V = 100 mV (peak) ripple R > (AC 0.28 V (p-p kHz; A-weighted i open loop R > Product specification TDA1314T TYP. MAX. UNIT bits 110 100 ...
Page 10
... T = ----------- f SCK where N = integer 0.35TM ----------- f SCK 0.35TM ----------- f SCK with sample-and-hold from DAC f > 22 kHz; no post filter Product specification TDA1314T TYP. MAX. UNIT 19.456 MHz s s 44.1 48 kHz 128 4f kHz 0. ...
Page 11
... Philips Semiconductors Quadruple filter DAC August 1994 12 Product specification TDA1314T ...
Page 12
... In total a 2nd order level of filtering can be found above 100 kHz. In terms of power the audio out-of-band power is approximately 15 the audio in-band power. 13 Product specification TDA1314T (pin 14) and ground ref is ref (pin 7) is also the SSA ...
Page 13
... Philips Semiconductors Quadruple filter DAC August 1994 14 Product specification TDA1314T ...
Page 14
... Philips Semiconductors Quadruple filter DAC PACKAGE OUTLINE 18.1 17.7 handbook, full pagewidth S 0.9 (4x) 0.4 28 pin 1 index 1 Dimensions in mm. Fig.7 Plastic small outline package; 28 leads; body width 7.5 mm (SO28; SOT136-1). August 1994 0 2.45 0.3 2.25 0.1 14 0.49 0.25 M 0.36 1.27 (28x) 15 Product specification TDA1314T 7.6 7.4 A 10.65 10.00 1.1 1.0 2.65 0.32 2.35 0.23 1 detail A MBC236 - 1 ...
Page 15
... C. (Pulse-heated soldering is not recommended for SO packages.) For pulse-heated solder tool (resistance) soldering of VSO packages, solder is applied to the substrate by dipping extra thick tin/lead plating before package placement. 16 Product specification TDA1314T - HELD SOLDERING ) ...