TDA9178T Philips Semiconductors, TDA9178T Datasheet - Page 10

• Manufacturer Part Number: TDA9178T
• Description: YUV one chip picture improvement based on luminance vector-/ colour vector- and spectral processor
• Manufacturer: Philips Semiconductors

Philips Semiconductors
Successive approximation ADC
Pins ADEXT1, ADEXT2 and ADEXT3 are connected to a
6-bit successive approximation ADC via a multiplexer.
The multiplexer toggles between the inputs with each field.
At each field flyback, a conversion is started for two of the
three inputs and the result is stored in the corresponding
bus register ADEXT1, ADEXT2 or ADEXT3. The input pin
ADEXT1 is updated every field, while input fields
ADEXT2 and ADEXT3 are updated once in two
consecutive fields (see Figs 7, 8, 9 and 10). Once in
32 fields the ADEXT2 input is not updated, because then
the noise measurement is updated.
In this way, any slow varying analog signal can be given
access to the I
the data of that register is made invalid by setting the flag
bit DV (Data Valid) to zero.
Smart noise control
With the help of the internal noise detector and a
user-preferred noise algorithm, the user can make a fully
automatic I
Noise Control’.
Demonstration mode
By the I
features can be demonstrated in one picture. By setting
bit DEM to logic 1, all the features selected by the user are
active for 5 s in 1f
another 5 s in 1f
selected are turned off (then the TDA9178 is ‘transparent’
to the incoming signal).
Internal window
To determine the histogram levels and the black offset the
TDA9178 performs several measurements. An internally
defined window serves to exclude parts in the scene like
‘subtitling’ or ‘logos’. The internal window can be regarded
as a weighting function which has a value of one within a
square near the centre of the screen and which gradually
decreases to zero towards the edges.
When bit WLB (Window Letter Box) is made logic 1, the
height of the window is reduced by a factor of
This prevents the contribution of the black bars above and
below a 16 : 9 scene to the measurements.
1999 Sep 24
YUV one chip picture improvement based on luminance
vector-, colour vector- and spectral processor
2
C-bus bit DEM all the picture improvement
2
C-bus feature reduction, briefly called ‘Smart
2
C-bus. If a register access conflict occurs,
H
H
mode (in 2f
mode (in 2f
H
H
mode: 2.5 s) all features
mode: 2.5 s), and for
2
3
.
10
I
The I
properly addressed command. Bit PDD (Power-Down
Detected) in the status register is set each time an
interruption of the power supply occurs and is reset only by
reading the status register. A 3-bit identification code can
also be read from the status register, which code can be
used to automatically configure the application by
software.
The input control registers can be written sequentially by
the I
increment feature or by addressing them directly.
The output control functions cannot be addressed
separately. Reading out the output control functions
always starts at subaddress 00H and all subsequent
words are read out by the automatic subaddress
increment procedure.
The bits in the I
except for bits AMS and VG5: therefore the TDA9178 is in
1.0 V luminance signal range and the variable gamma is
set to 20H (gamma correction 0%).
I
The slave address of the IC is given in Table “Slave
address”. If pin ADR of the TDA9178 is connected to
ground, the I
connected to pin DEC
The circuit operates on clock frequencies up to 400 kHz.
Slave address
Auto-increment mode is available for subaddresses.
2
2
ADR
C-bus
C-BUS SPECIFICATION
A6
2
2
C-bus by the embedded automatic subaddress
C-bus is always in standby mode and responds on a
A5
1
2
C-bus address is 40H; if pin ADR is
2
ADR
C-bus are preset to logic 0 at power-on
A4
DIG
A3
0
, the I
2
A2
C-bus address is E0H.
0
Preliminary specification
A1
0
TDA9178
A0
0
R/W
X