SA2002EPA Sames, SA2002EPA Datasheet
SA2002EPA
Related parts for SA2002EPA
SA2002EPA Summary of contents
Page 1
... Meets the IEC 521/1036 Specification requirements for Class 1 AC Watt hour meters Protected against ESD DESCRIPTION The SAMES SA2002E is an enhancement of the SA9602E, as the circuit contains the oscillator on chip. The SAMES SA2002E single phase uni-directional power/energy metering integrated circuit generates a pulse rate output with a frequency proportional to the power consumption ...
Page 2
... R V 1.1 R Symbol Min -150 PIN T -40 STG T -25 O 2/10 3 sames sames Max Unit Condition +85 °C 2.75 V -2. µA Peak value +25 µA +25 Peak value rated input conditions Hz Specified linearity 1600 Hz Min and Max frequency ...
Page 3
... Pulse rate output. Refer to pulse output format for a description 12 FOUT of the pulse rate. Leave pins unconnected. 4 TP1 5 TP2 TP3 6 7 TP4 9 TP5 10 TP6 TP7 11 13 TP8 15 TP9 16 TP10 17 TP11 TP12 18 3/ nominal mains voltage. The RMS at rated conditions. RMS SS sames sames ...
Page 4
... VREF 3 TP1 FOUT 6 TP2 7 TP3 8 DR-01486 Figure 4: Pin connections: Package: SOIC-16 ORDERING INFORMATION Part Number Package SA2002EPA DIP-8 SA2002EPA DIP-14 SA2002EPA DIP-20 SA2002ESA SOIC-16 SA2002ESA SOIC-20 http://www.sames.co.za 8 GND 7 IVP FOUT 5 Figure 3: Pin connections: Package: DIP-14 16 GND 15 IVP 14 ...
Page 5
... VDD VDD Pulse output FOUT VSS SA2002E VSS 5/ IIP CURRENT SENSOR I INPUTS V DD IIN IVP VOLTA GE SENSOR INPUT V GND DR-01148 Figure 7: Internal analog input configuration sames sames . The RMS at nominal RMS I V ...
Page 6
... An integrated anti-creep function does not allow output pulses on FOUT if no power is measured by the device. v MAINS POWER FOUT at RMS . The current into the RMS via resistor R5. 6/ DR-01282 t P Figure 8: FOUT instantaneous pulse output 71µs 71µs min. DR-01151 Figure 9: FOUT pulse width sames sames ...
Page 7
... A 5k trimpot will be used in the voltage channel for meter calibration. The center position on the pot is used in the calculations 2.5k and values for resistors R11 = 22k and R12 =1M is chosen. Substituting the values will result in 23.91k (230V/14. 333k so the resistor values of R1, R2 and R3 are chosen to be 110k 7/10 sames sames ...
Page 8
... SA2002E Figure 10: Application circuit using a shunt resistor for current sensing. http://www.sames.co.za 8/10 sames sames ...
Page 9
... Capacitor, 100uF, 16V, electrolytic C4 Capacitor, 330nF, 250VAC C5 Capacitor, 820nF C6 4N35, Opto Coupler U2 Note 1: Resistor (R6 and R7) values are dependant on the selected shunt resistor (R14) value. Note 2: Capacitor positioned as close as possible to supply pins. http://www.sames.co.za 9/10 sames sames Detail DIP-8 Note 1 Note 1 Note 2 ...
Page 10
... The information contained in this document is confidential and proprietary to South African Micro-Electronic Systems (Pty) Ltd ("SAMES") and may not be copied or disclosed to a third party, in whole or in part, without the express written consent of SAMES. The information contained herein is current as of the date of publication; however, delivery of this document shall not under any circumstances create any implication that the information contained herein is correct as of any time subsequent to such date ...