AN2520000408081B Yageo Corporation, AN2520000408081B Datasheet

no-image

AN2520000408081B

Manufacturer Part Number
AN2520000408081B
Description
Communication Misc, Multilayer Ceramic Antenna For Bluetooth/WLAN IEEE 802.11b and WLAN IEEE 802.11a (2.45/5.2Ghz) (Surface Mounted Ceramic Dual Band Antenna)
Manufacturer
Yageo Corporation
Datasheet
QUICK REFERENCE DATA
Dimension
Central Frequency*
Bandwidth
Gain*
VSWR
Polarization
Azimuth
Impedance
Operating Temperature
Termination
Resistance to soldering heats
Maximum Power
* Actual value will depend on size of customer ground plane
environmentally-friendly aqueous solvent technology. Termination is lead free (Pb free) and
packing materials can be re-cycled
1
HF R&D
Grant Lin/Cliff
spec.doc
All the technical data and information contained herein are subject to change without prior notice
FOR BLUETOOTH/WLAN IEEE 802.11b & WLAN IEEE 802.11a (2.45/5.2GHz)
Special Environmental Concerns- Green Products Design: The foil making process is using
Multilayer Ceramic Antenna
for IEEE802.11a & IEEE802.11b
Print date 02/10/03
Phycomp Taiwan Ltd.
(Surface Mounted Ceramic Dual Band Antenna)
MULTILAYER CERAMIC ANTENNA
Product Specification
>100 MHz
8.7* 8 * 0.9 mm
2.45 GHz /5.2GHz
3.5dBi max @5.2GHz
1.5dBi max @2.45GHz
2.5 max
Linear
Omni-directional
50 Ohm
-55~125 Deg. C
Ni/Sn (Environmentally-Friendly Leadless)
260 Deg. C, 10 sec.
1W
2002-10-02
1
Page
(Preliminary)
4311 117 00252
1
Preliminary internal use only
sheet 190-1
May 17, 02
Oct. 3, 02
A4

Related parts for AN2520000408081B

AN2520000408081B Summary of contents

Page 1

MULTILAYER CERAMIC ANTENNA FOR BLUETOOTH/WLAN IEEE 802.11b & WLAN IEEE 802.11a (2.45/5.2GHz) (Surface Mounted Ceramic Dual Band Antenna) QUICK REFERENCE DATA Dimension Central Frequency* Bandwidth Gain* VSWR Polarization Azimuth Impedance Operating Temperature Termination Resistance to soldering heats Maximum Power * ...

Page 2

APPLICATION Suggested Layout Ground plane(back side) Bluetooth module or other RF Module DIMENSIONAL DATA Figure R&D Print ...

Page 3

SOLDER LAND PATTERN Figure Typical Radiation Pattern Polar Plot (Based on 35*15 Test Board) -180 -10 -135 -20 -30 -40 -50 -60 -90 ...

Page 4

H-Plane HF R&D Print date 02/10/03 Multilayer Ceramic Antenna for IEEE802.11a & IEEE802.11b Grant Lin/Cliff spec.doc Phycomp Taiwan Ltd. -135 -225 -40 -30 -20 -10 -90 -270 ...

Page 5

CUSTOMERIZED TEST BOARD FOR RETURN LOSS SMA Connector 4 inch coaxial cable RG-316 Solder Joint 1 35mm 35mm Ground plane at back side Ground plane at back side 15mm 15mm RF RF Modules Modules 50 Ohm transmission line or coplanar ...

Page 6

RELIABILITY DATA (Reference to IEC Specification) IEC IEC 384-10/ 60068-2 CECC 32 TEST 100 METHOD CLAUSE 4.4 Mounting 4.5 Visual inspection and dimension check 4.6.1 Antenna 4.8 Adhesion 4.9 Bond strength of plating on end face HF R&D Print date ...

Page 7

IEC IEC 384-10/ 60068-2 CECC 32 TEST 100 METHOD CLAUSE 4.10 20(Tb) Resistance to soldering heat Resistance to leaching 4.11 20(Ta) Solderability 4.12 4(Na) Rapid change of temperature 4.14 3(Ca) Damp heat 4.15 Endurance HF R&D Print date 02/10/03 Multilayer ...

Page 8

ORDERING INFORMATION: Method I- by 12NC Ordering Code The antennas may be ordered by using the 12 NC ordering code. These code numbers can be determined by the following rules: 4311 252 ...

Page 9

Taping Blister Tape DIMENSION: Serial no 1 Sprocket hole 2 Pocket hole 3 Distance sprocket hole/sprocket hole 4 Distance pocket/pocket 5 Distance sprocket hole/pocket 6 Tape width 7 Distance sprocket hole/outside 8 Distance sprocket hole/pocket 9 Pocket length 10 Pocket ...

Page 10

Reel Specifications Product size Units per Tape Width code Reel Antenna 1000 HF R&D Print date 02/10/03 Multilayer Ceramic Antenna for IEEE802.11a & IEEE802.11b Grant Lin/Cliff spec.doc Phycomp Taiwan Ltd. C (mm) (mm) (mm) 16 180.0±1.0 62±0.5 4311 117 ...

Related keywords