LM10A-Y1 Osram Opto Semiconductors, LM10A-Y1 Datasheet - Page 4

• Manufacturer Part Number: LM10A-Y1
• Description: Linearlight Flex
• Manufacturer: Osram Opto Semiconductors

Assembly Information
Ordering Guide
Productgroup
LINEARlight Flex
LINEARlight Flex
LINEARlight Flex
LINEARlight Flex
LINEARlight Flex
LINEARlight Flex
LINEARlight Flex
LINEARlight Flex
LINEARlight Flex
LINEARlight Flex
LINEARlight Flex
*)
Note: Typical performance data are subject to change without any further notice, particularly as LED technology evolves.
Sales and Technical Support
Related and Further Information
LM10A - 20.07.2007
EAN: Ordering number per single module
S-Unit: Modules per shipping unit
Connection with soldering wires on unmounted module: Do not pretin the solderpads but pretin the wires and solder for max 4 s at
300 °C. Allow solderpoints to completely cool down before the next soldering. Prevent shear- or peel forces.
Soldering of wires with the module mounted on a heatsink: Pretin solderpads and wires and solder for max 3 s at 350 °C. Allow
solderpoints to completely cool down before the next soldering. Prevent shear- or peel forces.
The smallest unit (140 mm- 10 LEDs) can be removed by cutting with scissors between the designated solder pads.
The mounting of the module is facilitated by means of the double-sided adhesive on the back-surface of the module. Care must be
taken to provide a clean and dry mounting surface, free of oils or silicone coatings as well as dirt particle. The mounting substrate
must have sufficient structural integrity. Take care to completely remove the protective backing. Once the module is appropriately
positioned, press on the module with about 20N/cm² (refer to application techniques of 3M adhesive transfer tapes). In difficult
cases the use of a primer may help.
The minimum bending radius is 2 cm. The module may be bent over a smaller radius but only in regions of the circuit board
containing no electronic components and such bends should be made once and fixed in position to avoid cyclic fatigue.
The thermal length expansion coefficient of the modul is 17*10^-6cm/cm/K. When installing in environments with large variations in
temperature (e.g. outdoor applications) and operating length of more than 2 m, the use of metallic mounting surfaces is necessary.
Otherwise it is advisable to use an additional thicker adhesive tape to absorb the stress of any mismatch in expansion coefficients.
The new dimension of light
New creativity in lighting design
LED Modules for illuminated signs
OPTOTRONIC® Technical Guide
OPTOTRONIC® Data Sheets
OSRAM LED systems
Datasheet CONNECTsystem LM-xx Flex
OSRAM GmbH
Hellabrunner Strasse 1
D - 81536 München
Germany
www.osram.com
[phone]
Productname
LM10A-W2-865
LM10A-W1-865
LM10A-W2-854
LM10A-W1-854
LM10A-W2-847
LM10A-W1-847
LM10A-W3-727
LM10A-A1
LM10A-Y1
LM10A-T2
LM10A-B1
Page 4 of 4
Sales and technical support is given by the
local OSRAM subsidiaries.
On our world wide homepage all OSRAM
subsidiaries are listed with complete
address and phone numbers.
153 S006 GB
138 W002 GB
130 T008 GB
http://catalog.myosram.com
www.osram.com/led-systems
www.osram.com/led-systems-downloads
EAN *
4050300887265
4050300873817
4050300887289
4050300817170
4008321040145
4050300817156
4008321186171
4008321040060
4050300946030
4008321168832
4050300945491
S-Unit *
8
8
8
8
8
8
8
8
8
8
8