LTC1414 Linear Technology, LTC1414 Datasheet - Page 12

• Manufacturer Part Number: LTC1414
• Description: 14-Bit/ 2.2Msps/ Sampling A/D Converter
• Manufacturer: Linear Technology

APPLICATIONS
LTC1414
The V
shown in Figure 11. This is useful in applications where the
peak input signal amplitude may vary. The input span of
the ADC can then be adjusted to match the peak input
signal, maximizing the signal-to-noise ratio. The filtering
of the internal LTC1414 reference amplifier will limit the
bandwidth and settling time of this circuit. A settling time
of 5ms should be allowed after a reference adjustment.
Differential Inputs
The LTC1414 has a unique differential sample-and-hold
circuit that allows rail-to-rail inputs. The ADC will always
convert the difference of A
common mode voltage. The common mode rejection
holds up to extremely high frequencies, see Figure 12. The
only requirement is that neither input can exceed the AV
or AV
rors (INL) and differential nonlinearity errors (DNL) are
independent of the common mode voltage, however, the
bipolar zero error (BZE) will vary. The change in BZE is
typically less than 0.1% of the common mode voltage.
Dynamic performance is also affected by the common
mode voltage. THD will degrade as the inputs approach
either power supply rail, from –84dB with a common
mode of 0V to –75dB with a common mode of 2.5V
or –2.5V.
Full-Scale and Offset Adjustment
Figure 13 shows the ideal input/output characteristics for
the LTC1414. The code transitions occur midway between
successive integer LSB values (i.e., – FS + 0.5LSB,
– FS + 1.5LSB, – FS + 2.5LSB,...FS – 2.5LSB, FS – 1.5LSB).
12
SS
REF
power supply voltages. Integral nonlinearity er-
pin can be driven with a DAC or other means
LTC1450
Figure 11. Driving V
U
ANALOG INPUT
DIFFERENTIAL
INFORMATION
U
2V TO 3V
IN
2V TO 3V
+
– (A
10 F
REF
IN
with a DAC
W
1
2
3
4
5
–
) independent of the
A
A
V
REFCOMP
AGND
IN
IN
REF
+
–
LTC1414
U
1414 F11
DD
The output is two’s complement binary with
1LSB = FS – (– FS)/16384 = 5V/16384 = 305.2 V.
In applications where absolute accuracy is important,
offset and full-scale errors can be adjusted to zero. Offset
error must be adjusted before full-scale error. Figure 14
shows the extra components required for full-scale error
adjustment. Zero offset is achieved by adjusting the offset
applied to the A
– 152 V (i.e., – 0.5LSB) at A
A
0000 0000 00 and 1111 1111 1111 11. For full-scale
adjustment, an input voltage of 2.499544V (FS – 1.5LSBs)
is applied to A
code flickers between 0111 1111 1111 10 and
0111 1111 1111 11.
IN
–
input until the output code flickers between 0000
Figure 13. LTC1414 Transfer Characteristics
011…111
011…110
011…101
000…000
111…111
100…010
100…001
100…000
80
70
60
50
40
30
20
10
0
Figure 12. CMRR vs Input Frequency
1k
IN
–(FS – 1LSB)
IN
+
–
and R2 is adjusted until the output
10k
INPUT FREQUENCY (Hz)
input. For zero offset error apply
IN
100k
INPUT RANGE
+
and adjust the offset at the
0
1M
LTC1414 • F12
FS – 1LSB
LTC1414 • F13
10M