LTC1478 Linear Technology, LTC1478 Datasheet

no-image

LTC1478

Manufacturer Part Number
LTC1478
Description
Single and Dual Protected High Side Switches
Manufacturer
Linear Technology
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LTC1478CS
Manufacturer:
LT
Quantity:
992
Part Number:
LTC1478CS
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC1478CS#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIONS
SI PLIFIED BLOCK
FEATURES
EN
W
Extremely Low R
No Parasitic Body Diode
Built-In Short-Circuit Protection: 2A
Built-In Thermal Overload Protection
Operates from 2.7V to 5.5V
Inrush Current Limited
Ultralow Standby Current: 0.01 A
Built-In Charge Pump
Controlled Rise and Fall Times: t
Single Switch in 8-Pin SO Package
Dual Switch in Narrow 16-Pin SO Package
Notebook Computer Power Management
Power Supply/Load Protection
Supply/Battery Switch-Over Circuits
Circuit Breaker Function
"Hot Swap" Board Protection
Peripheral Power Protection
CONTROL LOGIC
GATE CHARGE
DISCHARGE
CHARGE
PUMP
AND
*NMOS SWITCHES WITH NO PARASITIC BODY DIODES
V
U
INS
DS(ON)
CURRENT LIMIT
AND THERMAL
SHUTDOWN
Switch: 0.07
DIAGRAM
V
*
R
IN1
= 1ms
V
*
IN2
W
V
*
IN3
LTC1477/1478 • TA01
V
OUT
Single and Dual Protected
DESCRIPTION
The LTC
provide extremely low R
protection against short-circuit and thermal overload con-
ditions. A built-in charge pump generates gate drive
higher than the supply voltage to fully enhance the internal
NMOS switch. This switch has no parasitic body diode and
therefore no current flows through the switch when it is
turned off and the output is forced above the input supply
voltage. (DMOS switches have parasitic body diodes that
become forward biased under these conditions.)
Two levels of protection are provided by the
LTC1477/LTC1478. The first level of protection is short-
circuit current limit which is set at 2A. The short-circuit
current can be reduced to as low as 0.85A by disconnect-
ing portions of the power device (see Applications Infor-
mation). The second level of protection is provided by
thermal overload protection which limits the die tempera-
ture to approximately 130 C.
The LTC1477 single is available in 8-lead SO packaging.
The LTC1478 dual is available in 16-lead SO packaging.
, LTC and LT are registered trademarks of Linear Technology Corporation.
®
1477/LTC1478 protected high side switches
5.20
5.10
4.70
4.60
5.00
4.90
4.80
0
High Side Switches
T
V
A
IN1
U
0.25
= 25 C
Switch Output Voltage
= V
IN2
LTC1477/LTC1478
OUTPUT CURRENT (A)
0.5
= V
DS(ON)
IN3
0.75
= V
INS
switching with built-in
= 5V
1.00
LTC1477/1478 • TP02
1.25
1.50
1

Related parts for LTC1478

LTC1478 Summary of contents

Page 1

... Applications Infor- mation). The second level of protection is provided by thermal overload protection which limits the die tempera- ture to approximately 130 C. The LTC1477 single is available in 8-lead SO packaging. The LTC1478 dual is available in 16-lead SO packaging. , LTC and LT are registered trademarks of Linear Technology Corporation ...

Page 2

... AV 3 INS AEN 4 GND IN3 S8 PART MARKING BV 7 IN2 BV 8 OUT 1477 16-LEAD PLASTIC SO T JMAX = 25 C, unless otherwise noted. Each channel of the LTC1478 is tested separately (Note IN1 IN2 IN3 OUT = 3.3V IN1 IN2 ...

Page 3

... 470 F OUT OUT OUT OUT ALL V PINS = –0.4 0 0.4 0.8 1.2 1.6 2.0 TIME (ms) LTC1477/1478 • TPC08 LTC1477/LTC1478 Switch Resistance (5V) 0.30 0.25 0. INS IN1 IN2 IN3 = NC 0.15 0.10 ALL V PINS = 5V IN 0.05 PINS JUNCTION TEMPERATURE ( C) Output Current (5V) ...

Page 4

... IN3 , BV and BV supply pins for lowest ON INS IN1 , BV pins are con IN2 , is connected to the drain of approxi- IN3 and BV pins can be selectively discon- IN3 . (See Applications Information DS(ON) (Pins 1,16; 8,9): The outputs of the LTC1478 INS INS , IN2 , AV , IN3 , IN2 ...

Page 5

... C which limits the power dissipation to safe levels. LTC1478 Operation The LTC1478 dual protected switch can be thought of as two independent LTC1477 single protected switches. The input supply voltages may be from separate power sources. The ground connection, however, is common to both channels and must be connected to the same potential ...

Page 6

... LTC1477/LTC1478 U U APPLICATIONS INFORMATION ing of the switch parameters to the expected load current and system current limit requirements. A couple of examples are helpful nominal load of 1A was controlled by the switch configured to current limit at 2A (all V together), the R would be 0.07 and the voltage DS(ON) drop across the switch would be 70mV. The power dissipated by the switch would only be 70mW ...

Page 7

... OUT 22 H SUMIDA MBRS130LT3 CD54-220 (5V SENSE LIM + 100 F LT1304CS8-5 1 10V LBI TANT 7 2 SHDN LBO 5 LTC1477/LTC1478 D1 L1* MBRS130LT3 10 H 12V SENSE + 47 F LT1301 16V 0.1 F TANT LIM GND 1 DN117 • F03 5V/2A OR 3.3V/2A + 100 F 1k 10V LTC1477/1478 • TA08 ...

Page 8

... LTC1477/LTC1478 PACKAGE DESCRIPTION 0.010 – 0.020 45 (0.254 – 0.508) 0.008 – 0.010 0 – 8 TYP (0.203 – 0.254) 0.016 – 0.050 0.406 – 1.270 * DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE ** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" ...

Related keywords