LTC2242-10 Linear Technology, LTC2242-10 Datasheet - Page 14

• Manufacturer Part Number: LTC2242-10
• Description: 250Msps ADC
• Manufacturer: Linear Technology

www.datasheet4u.com
APPLICATIONS INFORMATION
LTC2242-10
DYNAMIC PERFORMANCE
Signal-to-Noise Plus Distortion Ratio
The signal-to-noise plus distortion ratio [S/(N + D)] is
the ratio between the RMS amplitude of the fundamen-
tal input frequency and the RMS amplitude of all other
frequency components at the ADC output. The output is
band limited to frequencies above DC to below half the
sampling frequency.
Signal-to-Noise Ratio
The signal-to-noise ratio (SNR) is the ratio between the
RMS amplitude of the fundamental input frequency and
the RMS amplitude of all other frequency components
except the fi rst fi ve harmonics and DC.
Total Harmonic Distortion
Total harmonic distortion is the ratio of the RMS sum
of all harmonics of the input signal to the fundamental
itself. The out-of-band harmonics alias into the frequency
band between DC and half the sampling frequency. THD
is expressed as:
where V1 is the RMS amplitude of the fundamental fre-
quency and V2 through Vn are the amplitudes of the second
through nth harmonics. The THD calculated in this data
sheet uses all the harmonics up to the fi fth.
Intermodulation Distortion
If the ADC input signal consists of more than one spectral
component, the ADC transfer function nonlinearity can
produce intermodulation distortion (IMD) in addition to
THD. IMD is the change in one sinusoidal input caused
by the presence of another sinusoidal input at a different
frequency.
If two pure sine waves of frequencies fa and fb are ap-
plied to the ADC input, nonlinearities in the ADC transfer
function can create distortion products at the sum and
difference frequencies of mfa ± nfb, where m and n = 0,
1, 2, 3, etc. The 3rd order intermodulation products are
14
THD = 20Log
⎛
⎝ ⎜
(
V2
2
+ V3
2
+ V4
2
+ ...Vn
2
)
/ V1
⎞
⎠ ⎟
2fa + fb, 2fb + fa, 2fa – fb and 2fb – fa. The intermodula-
tion distortion is defi ned as the ratio of the RMS value of
either input tone to the RMS value of the largest 3rd order
intermodulation product.
Spurious Free Dynamic Range (SFDR)
Spurious free dynamic range is the peak harmonic or spuri-
ous noise that is the largest spectral component excluding
the input signal and DC. This value is expressed in decibels
relative to the RMS value of a full scale input signal.
Full Power Bandwidth
The full power bandwidth is that input frequency at which
the amplitude of the reconstructed fundamental is reduced
by 3dB for a full scale input signal.
Aperture Delay Time
The time from when a rising ENC
to the instant that the input signal is held by the sample
and hold circuit.
Aperture Delay Jitter
The variation in the aperture delay time from conversion
to conversion. This random variation will result in noise
when sampling an AC input. The signal to noise ratio due
to the jitter alone will be:
CONVERTER OPERATION
As shown in Figure 1, the LTC2242-10 is a CMOS pipelined
multi-step converter. The converter has fi ve pipelined ADC
stages; a sampled analog input will result in a digitized
value fi ve cycles later (see the Timing Diagram section). For
optimal performance the analog inputs should be driven
differentially. The encode input is differential for improved
common mode noise immunity. The LTC2242-10 has two
phases of operation, determined by the state of the dif-
ferential ENC
refer to ENC
less than ENC
SNR
JITTER
+
+
= –20log (2π • f
–
/ENC
greater than ENC
as ENC low.
–
input pins. For brevity, the text will
IN
+
–
• t
equals the ENC
as ENC high and ENC
JITTER
)
–
voltage
224210fc
+