LTC2641 Linear Technology, LTC2641 Datasheet - Page 5

• Manufacturer Part Number: LTC2641
• Description: (LTC2641 / LTC2642) 16-/14-/12-Bit VOUT DACs
• Manufacturer: Linear Technology

ELECTRICAL CHARACTERISTICS
TIMING CHARACTERISTICS
temperature range, otherwise specifi cations are at T
otherwise specified.
range, otherwise specifi cations are at T
SYMBOL
I
C
V
Power Supply
V
I
P
SYMBOL
t
t
t
t
t
t
t
t
t
f
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Continuous operation above the specifi ed maximum operating
junction temperature may impair device reliability.
Note 3: LTC2641-16/LTC2642-16 ±1LSB = ±0.0015% = ±15.3ppm of full
scale. LTC2641-14/LTC2642-14 ±1LSB = ±0.006% = ±61ppm of full scale.
LTC2641-12/LTC2642-12 ±1LSB = ±0.024% = ±244ppm of full scale.
IN
DD
1
2
3
4
5
6
7
8
9
SCLK
IN
H
DD
D
www.DataSheet4U.com
PARAMETER
Digital Input Current
Digital Input Capacitance
Hysteresis Voltage
Supply Voltage
Supply Current, V
Power Dissipation
PARAMETER
DIN Valid to SCLK Setup Time
DIN Valid to SCLK Hold Time
SCLK Pulse Width High
SCLK Pulse Width Low
⎯ C ⎯ S Pulse High Width
LSB SCLK High to ⎯ C ⎯ S High
⎯ C ⎯ S Low to SCLK High
⎯ C ⎯ S High to SCLK Positive Edge
⎯ C ⎯ L ⎯ R Pulse Width Low
SCLK Frequency
V
DD
High to ⎯ C ⎯ S Low (Power-Up Delay)
DD
A
= 25°C. V
DD
A
The
= 3V or 5V, V
= 25°C. V
CONDITIONS
V
(Note 6)
Digital Inputs = 0V or V
Digital Inputs = 0V or V
Digital Inputs = 0V or V
CONDITIONS
50% Duty Cycle
IN
●
The
= GND to V
denotes the specifi cations which apply over the full operating temperature
●
DD
denotes the specifi cations which apply over the full operating
= 3V or 5V, V
REF
CC
Note 4: R
Note 5: Reference input resistance is code dependent. Minimum is at
871Chex (34,588) in unipolar mode and at 671Chex (26, 396) in bipolar
mode.
Note 6: Guaranteed by design and not production tested.
Note 7: Guaranteed by gain error and offset error testing, not production
tested.
= 2.5V, C
DD
DD
DD
OUT
, V
, V
REF
L
DD
DD
= 10pF, GND = 0, R
tolerance is typically ±20%.
= 2.5V, C
= 5V
= 3V
L
LTC2641/LTC2642
= 10pF, GND = 0, R
●
●
●
●
●
●
●
●
●
●
●
●
●
●
L
MIN
= ∞ unless otherwise specified.
MIN
2.7
10
10
15
0
9
9
8
8
8
0.15
0.60
0.36
TYP
120
TYP
30
3
L
= ∞ unless
MAX
MAX
200
5.5
±1
10
50
UNITS
UNITS
26412f
5
MHz
mW
mW
μA
μA
pF
ns
ns
ns
ns
ns
ns
ns
ns
ns
μs
V
V