LTC2931 Linear Technology, LTC2931 Datasheet - Page 11

• Manufacturer Part Number: LTC2931
• Description: Confi gurable Six Supply Monitor
• Manufacturer: Linear Technology

www.DataSheet4U.com
APPLICATIONS INFORMATION
the negative voltage being sensed and the VREF pin, is
connected to the high impedance adjustable input (V4).
V
at ground. The negative trip voltage is calculated from:
In a negative adjustable application, the minimum value for
R4 is limited by the sourcing capability of VREF (±1mA).
With no other load on VREF , R4 (minimum) is:
Tables 2 and 3 offer suggested 1% resistor values for
various positive and negative supply adjustable
applications assuming 5% monitor thresholds.
Although all six supply monitor comparators have built-
in glitch immunity, bypass capacitors on V1 and V2 are
recommended because the greater of V1 or V2 is also the
V
V6 inputs are allowed.
Power-Down
On power-down, once any of the monitor inputs drops
below its threshold, RST is held at a logic low. A logic low
of 0.4V is guaranteed until both V1 and V2 drop below
1V. If the bandgap reference becomes invalid (V
typical), the LTC2931 will enter the 150μs setup period
when V
Watchdog Timer
The watchdog circuit monitors a microprocessor’s (μP)
activity. The μP is required to change the logic state of the
WDI pin on a periodic basis in order to clear the watchdog
timer. Whenever RST is low, the watchdog timer is cleared
and WDO is set high. The watchdog timer starts when RST
goes high. Subsequent edges received on the WDI pin
clear the watchdog timer. The watchdog timer continues
to run until it times out. Once it times out, internal circuitry
brings the WDO pin low. WDO remains low for one reset
timeout period unless it is cleared by another edge on the
WDI pin or RST goes low. WDO toggles between high and
REF
CC
V
1.210V
for the device. Filter capacitors on the V3, V4, V5 and
TRIP
1mA
provides the necessary level shift required to operate
CC
= –V
rises above 2.4V max.
=1.210kΩ
REF
•
R3
R4
; V
REF
= 1.210V Nominal
CC
< 2V
low as long as the watchdog and reset timers are allowed
to time out repeatedly.
To disable the watchdog timer, simply ground the CWT
pin (Pin 11). With CWT held at ground, any reset event
forces WDO high indefi nitely. It is safe to leave the WDI
pin unconnected because the weak internal pull-up (10μA
typical) pulls WDI high. Tying WDI to V1 or ground is also
allowed, but grounding the WDI pin forces the pull-up
current to be drawn continuously.
Selecting the Reset Timing Capacitor
The reset timeout period is adjustable in order to
accommodate a variety of microprocessor applications.
The reset timeout period, t
a capacitor, C
value of this capacitor is determined by:
Leaving the CRT pin unconnected generates a minimum
reset timeout of approximately 25μs. Maximum reset
timeout is limited by the largest available low leakage
capacitor. The accuracy of the timeout period is affected
by capacitor leakage (the nominal charging current is 2μA)
and capacitor tolerance. A low leakage ceramic capacitor
is recommended.
Selecting The Watchdog Timing Capacitor
The watchdog timeout period is adjustable and can be
optimized for software execution. The watchdog timeout
period, t
between the CWT pin and ground. The value of this
capacitor is determined by:
Leaving the CWT pin unconnected generates a minimum
watchdog timeout of approximately 200μs. Maximum
watchdog timeout is limited by the largest available low
leakage capacitor. The accuracy of the timeout period is
affected by capacitor leakage (the nominal charging current
is 2μA) and capacitor tolerance. A low leakage ceramic
capacitor is recommended.
C
C
RT
WT
=
=
WD
2MΩ
t
20MΩ
RST
t
, is adjusted by connecting a capacitor, C
WD
RT
= 500 pF / ms
, between the CRT pin and ground. The
= 50 pF / ms
⎡ ⎣
⎡ ⎣
RST
⎤ ⎦ • t
, is adjusted by connecting
⎤ ⎦ • t
RST
WD
LTC2931
11
2931fb
WT
,