LTC4440-5 Linear Technology, LTC4440-5 Datasheet
LTC4440-5
Related parts for LTC4440-5
LTC4440-5 Summary of contents
Page 1
... V sients. The powerful driver capability reduces switching losses in MOSFETs with high gate capacitances. The LTC4440-5’s pull-up has a peak output current of 1.1A and its pull-down has an output impedance of 1.85Ω. The LTC4440-5 features supply independent TTL/CMOS compatible input thresholds with 350mV of hysteresis. ...
Page 2
... LTC4440 ABSOLUTE MAXIMUM Supply Voltage V ....................................................... – 0.3V to 15V CC BOOST – TS ......................................... – 0.3V to 15V INP Voltage ............................................... – 0.3V to 15V BOOST Voltage (Continuous) ................... – 0.3V to 85V BOOST Voltage (100ms) .......................... – 0.3V to 95V TS Voltage (Continuous) ............................. – 70V U PACKAGE/ORDER INFORMATION TOP VIEW INP 1 GND GND 4 MS8E PACKAGE 8-LEAD PLASTIC MSOP = 125° ...
Page 3
... Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: The LTC4440-5 is guaranteed to meet performance specifications from 0°C to 85°C. Specifications over the –40°C to 85°C operating temperature range are assured by design, characterization and correlation with statistical process controls ...
Page 4
... LTC4440 TYPICAL PERFOR A CE CHARACTERISTICS Output High Voltage ( Supply Voltage 1mA 10mA I = 100mA BOOST-TS SUPPLY VOLTAGE (V) 4440-5 G04 V Supply Current CC vs Temperature 250 INP = GND 200 INP = V ...
Page 5
... BOOST (Pin 6): High Side Bootstrapped Supply. An exter- nal capacitor should be tied between this pin and TS (Pin 4). Normally, a bootstrap diode is connected between V (Pin 1) and this pin. Voltage swing at this pin is from CC V – drop of the bootstrap diode. LTC4440-5 www.DataSheet4U.com = BOOST = PLH t PHL –35 – ...
Page 6
... LTC4440 CTIO S Exposed Pad MS8E Package INP (Pin 1): Input Signal. TTL/CMOS compatible input referenced to GND (Pin 2). GND (Pins 2, 4): Chip Ground. V (Pin 3): Chip Supply. This pin powers the internal low CC side circuitry. A low ESR ceramic bypass capacitor should be tied between this pin and the GND pin (Pin 2). ...
Page 7
... MOSFET’s gate capacitance during high-to-low signal transitions. When the power MOSFET’s gate is pulled low (gate shorted to source through N1) by the LTC4440-5, its source (TS) is pulled low by its load (e.g., an inductor or resistor). The slew rate of the source/ of 6V. ...
Page 8
... D. Keep the copper trace between the driver output pin and ) BOOST–TS the load short and wide. E. When using the MS8E package, be sure to solder the exposed pad on the back side of the LTC4440-5 pack- age to the board. Correctly soldered to a 2500mm . The Q value G ...
Page 9
... U TYPICAL APPLICATIO S LTC4440-5 www.DataSheet4U.com 44405fa 9 ...
Page 10
... LTC4440-5 U TYPICAL APPLICATIO S 10 www.DataSheet4U.com 44405fa ...
Page 11
... TYP S6 Package 6-Lead Plastic TSOT-23 (Reference LTC DWG # 05-08-1636) 0.95 REF 1.22 REF 1.50 – 1.75 2.80 BSC 1.4 MIN (NOTE 4) 0.95 BSC 0.80 – 0.90 1.00 MAX 0.30 – 0.50 REF 0.09 – 0.20 (NOTE 3) LTC4440-5 www.DataSheet4U.com 0.52 (.0205 REF 3.00 ± 0.102 (.118 ± .004) (NOTE BOTTOM VIEW OF 1.10 0.86 EXPOSED PAD OPTION ( ...
Page 12
... LTC4440-5 U TYPICAL APPLICATIO 240W 42V-56V 0.56µ 1µF 1µF 48V IN 11V 100V 100V D1 – INP BOOST LTC4440-5ES6 5 TG GND 0.22µ 12V 11V IN A MMBT3904 6 4 15k 120Ω DRVA DRVB 1/ LTC3723EGN-2 215k 15 UVLO DPRG ...