TM10032ACIWG SPEC TIANMA, TM10032ACIWG SPEC Datasheet
TM10032ACIWG SPEC
Related parts for TM10032ACIWG SPEC
TM10032ACIWG SPEC Summary of contents
Page 1
... SPECIFICATION FOR LCD MODULE Model No. Prepared by: Checked by : Verified by : Approved by: TIANMA MICROELECTRONICS CO., LTD TM10032ACIWG Date: Date: Date: Date: Ver.1.0 ...
Page 2
REVISION RECORD Date Ref. Page Revision No. Revision Items 1/21 Check & Approval Ver.1.0 ...
Page 3
General Specifications: 1.1 Display type: FSTN 1.2 Display color*: Display color: Blue-Black Background: White 1.3 Polarizer mode: Transflective/Positive 1.4 Viewing Angle: 6:00 1.5 Driving Method: 1/32Duty 1/6 Bias 1.6 Lcd operation voltage: 1.7 Without Backlight 1.8 Controller: S6B0715A11-B0CZ 1.9 ...
Page 4
...
Page 5
0032A ...
Page 6
Circuit Block Diagram 5/21 Ver.1.0 ...
Page 7
Absolute Maximum Ratings Item Power Supply Voltage LCD Driving Voltage Operating Temperature Range Storage Temperature Range Symbol Min. Max 2.4 3.6 DD- 4.5 15.0 LCD T -20 + -30 +80 ST 6/21 Unit ...
Page 8
Electrical Specifications and Instruction Code 6.1 Electrical characteristics Item Supply Voltage (Logic) Supply Voltage (LCD Drive) High Input (V Signal Voltage Low (V Supply current (Logic) (V (Display character) DD Symbol Min DD- SS 2.8 V 6.5 ...
Page 9
Interface Signals Pin No. Symbol Level 7. C2- 8 C2+ 9 C1- 10 C1+ 11 C3+ 12 VOUT 13 VSS 0V 14 SID H/L 15 SCLK ...
Page 10
Interface Timing Chart Serial Interface Characteristics CS1B (CS2 = 1) RS DB6 0.9V DD (SCLK) DB7 (SID) Item Serial clock cycle SCLK high pulse width SCLK low pulse width Address setup time Address hold time Data setup time Data ...
Page 11
Instruction Code INSTRUCTION DESCRIPTION Instruction RS Read display data 1 Write display data 1 Read status 0 Display ON / OFF 0 Initial display line 0 Set reference voltage 0 mode Set reference voltage 0 register Set page address ...
Page 12
Optical Characteristics 7.1 Optical Characteristics Item Symbol θ Viewing Angle θ Contrast Ratio C Turn Response Time Turn T off off Condition =0° θ ≥2 r =0° θ =0° θ x ...
Page 13
Definition of Optical Characteristics 7.2.1 Definition of Viewing Angle Top Bottom 7.2.2 Definition of Contrast Ratio Contrast Ratio Measuring Conditions: 1) Ambient Temperature: 7.2.3 Definition of Response time t Turn on time Measuring Condition: 1) Operating Voltage: ...
Page 14
Reliability 8.1 Content of Reliability Test No. Test Item 1 High Temperature Storage Low Temperature 2 Storage High Temperature 3 Operation Low Temperature 4 Operation High Temperature 5 /Humidity Storage Temperature 6 Cycle Vibration Test 7 (package state) Shock ...
Page 15
Failure Judgment Criterion Criterion Item Basic √ √ √ √ √ √ √ √ √ Out of the basic Specification Specification Electrical √ √ √ √ √ specification Mechanical Specification ...
Page 16
QUALITY LEVEL Examination At T =25℃ Test (unless otherwise stated) Min. Under External illumination Visual eyesight condition, the Inspection distance between eyes and LCD is 25cm. Under Display illumination Defects eyesight display on inspection. Note: Major defects: ...
Page 17
Precautions for Use of LCD Modules 10.1 Handling Precautions 10.1.1 The display panel is made of glass. Do not subject mechanical shock by dropping it from a high place, etc. 10.1.2 If the display panel is ...
Page 18
Storage precautions 10.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 10.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored ...
Page 19
Appendix A Inspection items and criteria for appearance defects Items Contents Protective Glue Cover Tape Leakage Rainbow Wrong polarizer attachment Bubble between polarizer and glass Polarizer Scratches of polarizer Black spot (in viewing area) Black line (in viewing area) Progressive ...
Page 20
Appendix A Inspection item and criteria for appearance defects (continued) Items Contents Cracks on pads Cracks on contact side Glass Cracks Cracks on non-contact side Corner cracks Criteria ≤3mm ≤W/5 ≤T/2 ≤2mm ≤W/5 T/2<C< ≤3mm ...
Page 21
Appendix B Inspection items and criteria for display defects Items Contents Open segment or open common Short Wrong viewing angle Contrast radio uneven Crosstalk Pin holes and cracks in segment (DOT) Black spot (in viewing area) Black line (in viewing ...
Page 22
Appendix B Inspection items and criteria for display defects (continued) Items Content Transfor- mation of segment Critera Not counted Max. 2 defects allowed x<0.1mm 0.1mm≤x≤0.2mm x=(a+b)/2 Not counted Max. 1 defects allowed a<0.1mm 0.1mm≤a≤0.2mm Max.2 defects allowed 0.8W≤a≤1.2W a=measured value ...