sfp-gc-r MRV Communications, Inc., sfp-gc-r Datasheet

no-image

sfp-gc-r

Manufacturer Part Number
sfp-gc-r
Description
Copper Ethernet Sfps
Manufacturer
MRV Communications, Inc.
Datasheet
Datasheet
Datasheet
Copper Ethernet SFPs
SFP-GC-R and SFP-GA-R
Overview
MRV off ers two models of Ethernet SFPs that support Gigabit Ethernet functionality for copper media application.
The SFP-GC-R model supports Gigabit Ethernet with a 1000Base-T interface. It is designed for Layer 1 network devices
that do not incorporate an Ethernet MAC. The SFP-GA-R is designed for use in Layer 2 and higher protocol devices such
as switches and routers that do incorporate an Ethernet MAC. It supports Gigabit Ethernet with an auto-negotiating
1000Base-T interface. SFP-GC-R and SFP-GA-R models each support MDI/MDI-X auto-detection and jumbo packet sizes
9,600+ bytes.
Installed into MRV products with an available SFP port, the SFP-GC-R plug-ins provide a simple and cost-eff ective way
to merge copper and fi ber network segments.
The SFP-GA-R gives network administrators greater fl exibility in confi guring their SFP-enabled switches and routers,
allowing them to use less expensive copper cabling and interfaces for links of 100 meters or less.
The SFP-GC-R and SFP-GA-R do not convert between edge devices of diff erent speeds or duplex mode. Connected
edge devices must operate at the same speed and duplex mode to communicate. An edge device that supports auto-
negotiation may require specifi c interface settings for fi xed Gigabit Ethernet speed and duplex mode operation.
The SFP-GC-R uses the SFP’s RX_LOS pin for link indication. The SFP-GA-R is compatible with 1000Base-X autonegotiation,
but does not use the RX_LOS pin for link indication because RX_LOS is internally grounded. The SFP-GA-R and SFP-GC-R
SFPs support the 2-wire serial communication protocol outlined in the SFP MSA to communicate the link indication.
Application A: Gigabit Ethernet Copper-to-Fiber Conversion with Redundancy
SFP-GC-R SFPs are used in combination with the Fiber Driver Dual Multi-Rate Transponder
(EM316DMR3G-3R) to create edge-to-edge redundant Gigabit copper links.
Redundant GbE
Copper Links
Network
Switch/Router
Optical Communications Systems™
SFP-GC-Rs and optical SFPs
EM316DMR module with
in a 1-slot Chassis
1
Redundant GbE
Fiber Links
Highlights
SFP-GC-R - 1000Base-T for Layer 1 devices (no MAC)
SFP-GA-R - 1000Base-T for Layer 2 and above devices
(with MAC)
MDI/MDI-X automatic detection
Plug-and-play functionality
LOS support (SFP-GC-R)
Hot-swap support
Transmitter always on (no LIN support)
MSA compliance
Complete MRV SFP compatibility
1000 Base-T operation in host system with SGMII
interface
Switch/Router
Redundant GbE
Copper Links
Network

Related parts for sfp-gc-r

sfp-gc-r Summary of contents

Page 1

... SFP-GC-R and SFP-GA-R models each support MDI/MDI-X auto-detection and jumbo packet sizes 9,600+ bytes. Installed into MRV products with an available SFP port, the SFP-GC-R plug-ins provide a simple and cost-eff ective way to merge copper and fi ber network segments. The SFP-GA-R gives network administrators greater fl exibility in confi guring their SFP-enabled switches and routers, allowing them to use less expensive copper cabling and interfaces for links of 100 meters or less ...

Page 2

... Server 0° 70°C (32°F to 158°F) -40°C to 85°C (-40°F to 185°F) 85% maximum, non-condensing 1.5 W FCC Part 15 (Class A); IC (Class A); EMC Directive: Emission (Class A) and Immunity; RoHS Directive; China RoHS; WEEE Directive: Wheelie Bin Mark SFP-GC-R Yes CAT-5 100 1000 Base-T N/A N/A Yes No ...

Page 3

... Optical Communications Systems™ Datasheet Notes for SFP-GC-R and SFP-GA- default SFP-GC-R and SFP-GA-R are full duplex devices in prefered master mode. 2. Automatic crossover (MDI/MDIX) detection is enabled. External crossover cable is not required. 3. With a SERDES that does not support SGMII, modules will operate at 1000Base-T only. ...

Related keywords