sa1e-tan2c IDEC Corporation, sa1e-tan2c Datasheet - Page 8

• Manufacturer Part Number: sa1e-tan2c
• Description: Sa1e Miniature Photoelectric Switches
• Manufacturer: IDEC Corporation

SA1E Miniature Photoelectric Switches (Built-in Amplifier Type)
Specifications
Note 1: Maintain at least the distance shown below between the SA1E photoelectric switch and reflector.
Note 2: Cable length: 1m (50g when the cable length is 2m. 110g when the cable length is 5m.)
Note 3: Cable length: 1m (55g when the cable length is 2m. 120g when the cable length is 5m.)
8
• Connector Cable (for connector type)
Sensing Method
Type No.
Power Voltage
Current Draw
Sensing Range
Adjustable Sensing Range
Detectable Object
Hysteresis
Response Time
Sensitivity Adjustment
Sensing Range Adjustment
Light Source Element
Operation Mode
Control Output
LED Indicators
Interference Prevention
Degree of Protection
Extraneous Light Immunity
Operating Temperature
Operating Humidity
Storage Temperature
Insulation Resistance
Dielectric Strength
Vibration Resistance
Shock Resistance
Material
Attachments
Weight
(approx.)
Connection
Method
Core Wires
Number of
IAC-R5/R6/R7
IAC-RS1/RS2: 150 mm
The detection distance cannot be guaranteed if the reflector is deformed or the tape type reflector is applied on uneven surface.
4
Cable Type
Connector Type
Cable Type
Connector Type M8 connector (4-pin)
Straight, 2m
Right angle, 2m
Straight, 5m
Right angle, 5m
Type & Length
/ R8: 100 mm
12 to 24V DC (Operating range: 10 to 30V DC)
Equipped with reverse-polarity protection
Projector: 15 mA
Receiver: 20 mA
10m
(with sensitivity
adjustment)
15m
(without sensitivity
adjustment)
—
Opaque
—
1 ms maximum
Adjustable using a potentiometer (approx. 260°)
Through-beam type and polarized retroreflective type are also available without sensitivity
adjustment.
—
Infrared LED
Red LED
Light ON/Dark ON
NPN open collector or PNP open collector
30V DC, 100 mA maximum
Voltage drop: 1.2V maximum (BGS type: 2V maximum)
Short-circuit protection
Operation LED: Yellow
Stable LED:
Power LED:
—
IP67 (IEC 60529)
Sunlight: 10,000 lux maximum, Incandescent lamp: 5,000 lux maximum (at receiver)
–25 to +55°C (no freezing)
35 to 85% RH (no condensation)
–40 to +70°C (no freezing)
Between live part and mounting bracket: 20 MΩ minimum (500V DC megger)
Between live part and mounting bracket: 1000V AC, 50/60 Hz, 1 minute
Damage limits: 10 to 55 Hz, Amplitude 0.75 mm, 20 cycles in each of 3 axes
Damage limits: 500 m/s
Housing: PC/PBT, Lens: PC (Polarized retroreflective type: PMMA), Indicator cover: PC
Instruction sheet, Sensitivity control screwdriver
Projector: 30g
Receiver: 30g
(Note 2)
Projector: 10g
Receiver: 10g
ø3.5 mm, 3-core, 0.2 mm
Through-beam
SA1E-T
SA9Z-CM8K-4S2
SA9Z-CM8K-4L2
SA9Z-CM8K-4S5
SA9Z-CM8K-4L5
Green
Green (Through-beam type projector)
Type No.
30 mA
With sensitivity
adjustment:
2.5m (IAC-R5/R8)
1.5m (IAC-R6)
1.3m (IAC-RS2)
1.0m (IAC-RS1)
0.8m (IAC-R7
Without sensitivity
adjustment:
3.0m (IAC-R5/R8)
2.0m (IAC-R6)
1.4m (IAC-RS2)
1.1m (IAC-RS1)
1.0m (IAC-R7
(Note 1)
Red LED
Two units can be mounted in close proximity.
2
30g (Note 2)
10g
(Note 1)
, 10 shocks in each of 3 axes
2
, 1-m vinyl cabtyre cable (2-core for the projector of through-beam type)
Retroreflective
Polarized
SA1E-P
Package
Quantity
)
)
1
700 mm
(using 200 × 200 mm
white mat paper)
Opaque/Transparent
20% maximum
Infrared LED
Diffuse-reflective
SA1E-D
• Air Blower Mounting Block
• Two mounting screws (M3 × 20 mm sems screws), one M5 × 6 mm screw for
• The air tube fitting and mounting bracket are not supplied and must be ordered
• Material: Anodized aluminum surface
Air Blower Mounting Block
plugging the air supply port, and one gasket (0.5 mm thick) are supplied.
separately (recommended mounting bracket: SA9Z-K01).
50 to 150 mm
(using 100 × 100 mm
white mat paper)
Red LED
Item
Small-beam
Reflective
SA1E-N
20 mm to preset
(using 200 × 200 mm
white mat paper)
40 to 200 mm
Opaque
10% maximum
—
6-turn control knob
Red LED
Operation LED:
Yellow
Stable LED: None
35g (Note 3)
20g
Suppression (BGS)
Background
SA9Z–A02
Type No.
SA1E-B
Package Quantity
5 to 35 mm
(using 100 × 100 mm
white mat paper)
—
Opaque/Transparent
20% maximum
Adjustable using a
potentiometer
(approx. 260°)
—
Infrared LED
Operation LED:
Yellow
Stable LED: Green
30g (Note 2)
10g
Convergent
Reflective
SA1E-G
1
(07/03/06)