ltl912seksa-l LiteOn Technology Corp., ltl912seksa-l Datasheet
ltl912seksa-l
Available stocks
Related parts for ltl912seksa-l
ltl912seksa-l Summary of contents
Page 1
... Selection Guide Part No. LTL912SEKSA-L Benefits Fewer LEDs Required Lower lighting System Cost Applications Automotive Lighting Signs and Signals Room Lighting Part No. : LTL912SEKSA-L BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Color Φv (lm) Red 3.75 Va(deg.) λd(nm) ...
Page 2
... LED materials etc., which allow designers to match the color of popular lighting applications, such as automotive lighting and electronic signs. Devices Part No. LTL912SEKSA-L Part No. : LTL912SEKSA-L BNS-OD-C131/ Source Color Lens Water Clear ...
Page 3
... All dimensions are in millimeters (inches). 2. Protruded resin is 1.0mm (.04") max. 3. Lead spacing is measured where the leads emerge from the package. 4. Specifications are subject change to without notice. 5. Copper alloy with plating Ag. Part No. : LTL912SEKSA-L BNS-OD-C131/ Page : 3 ...
Page 4
... LED Junction Temperature Soldering Preheat Temperature Lead Soldering Temperature Notes: 1. Operation at currents below 10mA is not recommended. 2. Operation in reverse bias is not recommended. 3. Derating linear as shown in Fig. 4 Part No. : LTL912SEKSA-L BNS-OD-C131/ °C Maximum Rating 242 70 100 0 ...
Page 5
... The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. Part No. : LTL912SEKSA-L BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION ...
Page 6
... FORWARD VOLTAGE (V) Fig. 2 Forward Current VS Forward Voltage 1.2 1 0.8 0.6 0.4 0 Forwrad Current If (mA) Fig. 4 Relative Intensity VS Forward Current Part No. : LTL912SEKSA-L BNS-OD-C131/ Fig. 1 Relative Intensity VS Wavelength 2.5 2.7 2.9 3.1 0 Fig. 3 Forward Current VS Ambient Temperature ...
Page 7
... A 0.6 B 1.0 C 1.5 D 2.0 E 2.5 F 3.0 G 3.5 H 4.0 J 5.0 L 6.0 Forward Voltage Bin Code Part No. : LTL912SEKSA-L BNS-OD-C131/ Bin Table Specification Category Code F 4 =25℃ A Maximum 0.35 0.55 0.8 1.2 1.8 2.4 3.0 3.6 4.2 4.8 6.1 7.3 9.7 (Volt) @I =70mA, T =25℃ Minimum Maximum 2 ...
Page 8
... Inner carton: 13 Anti rust bags x 11 Tubes x 65pcs = 9,295 pcs Dim: 530mm x 175mm x 128mm 3. Outer carton: 4 Inner cartons x 9,295 pcs = 37,180 pcs Dim: 545mm x 370mm x 280mm Part No. : LTL912SEKSA-L BNS-OD-C131/ Page : ...
Page 9
... Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR re-flow is not suitable process for through whole type Piranha LED production. Part No. : LTL912SEKSA-L BNS-OD-C131/ ...
Page 10
... Part No. : LTL912SEKSA-L BNS-OD-C131/ Wave Solder Temperature Profile Peak 2.5sec (Time =5sec) max 235℃ ...
Page 11
... To verify for ESD damage, check for “light up” and Vf of the suspect LEDs at low currents. The Vf of “good” LEDs should be >2.0V@0.1mA for InGaN product and >1.4V@0.1mA for AlInGaP product. Part No. : LTL912SEKSA-L BNS-OD-C131/ ...
Page 12
... Liteon may make process or materials changes affecting the performance or other characteristics of our products. These products supplied after such changes will continue to meet published specifications, but may not be identical to products supplied as samples or under prior orders. Part No. : LTL912SEKSA-L BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION ...