c-13-155-fdfb-slc8a-g5 Source Photonics, Inc., c-13-155-fdfb-slc8a-g5 Datasheet
c-13-155-fdfb-slc8a-g5
Related parts for c-13-155-fdfb-slc8a-g5
c-13-155-fdfb-slc8a-g5 Summary of contents
Page 1
... Single +3.3V Power Supply LVPECL Differential Inputs and Outputs Class 1 Laser International Safety Standard IEC 825 Compliant Solderability to MIL-STD-883, Method 2003 Flammability to UL94V0 Humidity RH 5-85% (5-95% short term) to IEC 68-2-3 Complies with Bellcore GR-468-CORE Uncooled laser diode with MQW structure ATM 155Mb/s Links RoHS compliance available Symbol Min ...
Page 2
... Data Input Current-Low Data Input Current-High Data Input Voltage-Low Data Input Voltage-High Note 6: Maximum current is specified at V Note 7: These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs P/N: C-13-155(C)-FDFB-SLC8A-G5 155 Mbps Single Mode SFF LC Transceiver Symbol Min. ...
Page 3
... Signal Detect Output Voltage-Low Signal Detect Output Voltage-High Note 9: The current excludes the output load current Note 10: These outputs are compatible with 10K, 10KH and 100KECL and LVPECL outputs. Note 11: C-13-155-FDFB-SLC8A-G5, LVPECL. Note 12: C-13-155C-FDFB-SLC8A-G5, LVTTL. P/N: C-13-155(C)-FDFB-SLC8A-G5 155 Mbps Single Mode SFF LC Transceiver Symbol Min ...
Page 4
... Directly connect this pin to the Transmitter ground plane Transmitter Disable (LVTTL) Transmitter Data In (LVPECL) Transmitter Data In Bar (LVPECL) The attaching posts are at case potential and may be connected to chassis ground. They are isolated from circuit ground DS-5477 Rev 0.0 2009-04-30 ...
Page 5
... Recommended Interface Circuit C-13-155-FDFB-SLC8A-G5 TERMINATE AT TRANSCEIVER INPUTS Ω 100 Ω 130 NOTE:C1=C2=C3=100nF P/N: C-13-155(C)-FDFB-SLC8A-G5 155 Mbps Single Mode SFF LC Transceiver Ω Z=50 Ω Z=50 Ω 130 6 Vcc(+3.3V) μ μ μ Ω Z=50 100 Ω ...
Page 6
... The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. ...
Page 7
... This way, the grounding clip brushes the edge of the cutout in order to make a proper contact. The use of a grounding clip also provides increased electrostatic protection and helps reduce radiated emission from the module or the host circuit board through the chassis faceplate ...
Page 8
... Recommended Board Layout Hole Pattern DIMENSION IN MILLIMETER (INCHES) NOTES: 1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER. 2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS. 3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY. ...
Page 9
... Package Diagram 48.8 (1.921) 10.50 (0.413) 1.00±0.05 (0.039±0.002) P/N: C-13-155(C)-FDFB-SLC8A-G5 155 Mbps Single Mode SFF LC Transceiver +0 -0.2 +( .000 ) -(0.008) 0.50 (0.020) 1.78 7.12 5.08 (0.070) (0.280) (0.200) 17.78 (0.700 6.25 (0.246) DS-5477 Rev 0.0 2009-04-30 ...
Page 10
... Ordering Information Table 8 – Order Information Part No. C-13-155-FDFB-SLC8A-G5 C-13-155C-FDFB-SLC8A-G5 Part Numbering Definition 155(C) - FDFB - Power Temperature -RoHS ● Wavelength 1310nm ● Communication protocol 155 = 155 Mbps LVPECL SD Output 155C = 155 Mbps LVTTL SD Output ● +3.3V Transceiver, DFB ● Single mode fiber ● ...
Page 11
... Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. Source Photonics customers using or selling products for use in such applications their own risk and agree to fully defend and indemnify Source Photonics for any damages resulting from such use or sale. ...