lt1054cs8-pbf Linear Technology Corporation, lt1054cs8-pbf Datasheet - Page 5

• Manufacturer Part Number: lt1054cs8-pbf
• Description: Switched-capacitor Voltage Converter With Regulator
• Manufacturer: Linear Technology Corporation

PIN
FB/SHDN (Pin 1): Feedback/Shutdown Pin. This pin has
two functions. Pulling Pin 1 below the shutdown threshold
( 0.45V) puts the device into shutdown. In shutdown the
reference/regulator is turned off and switching stops. The
switches are set such that both C
charged through the output load. Quiescent current in
shutdown drops to approximately 100 A (see Typical
Performance Characteristics). Any open-collector gate can
be used to put the LT1054 into shutdown. For normal
(unregulated) operation the device will start back up when
the external gate is shut off. In LT1054 circuits that use the
regulation feature, the external resistor divider can provide
enough pull-down to keep the device in shutdown until the
output capacitor (C
applications where the LT1054 would be run intermittently,
this does not present a problem because the discharge time
of the output capacitor will be short compared to the off-
time of the device. In applications where the device has to
start up before the output capacitor (C
charged, a restart pulse must be applied to Pin 1 of the
LT1054. Using the circuit of Figure 5, the restart signal can
be either a pulse (t
the restart signal into Pin 1 will allow the output voltage to
come up and regulate without overshoot. The resistor
divider R3/R4 in Figure 5 should be chosen to provide a
signal level at pin 1 of 0.7V to 1.1V.
TYPICAL PERFOR
U
FUNCTIONS
U
–12.6
–11.6
–11.8
–12.0
–12.2
–12.4
–4.7
–4.8
–4.9
–5.0
–5.1
p
–50
> 100 s) or a logic high. Diode coupling
Regulated Output Voltage
OUT
U
–25
) has fully discharged. For most
0
TEMPERATURE (°C)
W
25
A
U
50
IN
CE
and C
OUT
75
C
) has fully dis-
HARA TERISTICS
LT1054 • TPC09
100
OUT
125
are dis-
C
Pin 1 is also the inverting input of the LT1054’s error
amplifier and as such can be used to obtain a regulated
output voltage.
CAP
input capacitor (C
ground. When driven to V
When driven to ground Pin 2 sinks current to ground. Pin
4, the negative side of the input capacitor, is driven alter-
nately between ground the V
Pin 4 sinks current to ground. When driven to V
sources current from C
switches is unidirectional as should be expected using
bipolar switches.
V
also tied to the substrate of the device. Special care must
be taken in LT1054 circuits to avoid pulling this pin
positive with respect to any of the other pins. Pulling Pin
5 positive with respect to Pin 3 (GND) will forward bias the
substrate diode which will prevent the device from starting.
This condition can occur when the output load driven by the
LT1054 is referred to its positive supply (or to some other
positive voltage). Note that most op amps present just such
a load since their supply currents flow from their V
terminals to their V
lems with this type of load an external transistor must be
added as shown in Figure 1. This will prevent V
OUT
+
/CAP
(Pin 5): In addition to being the output pin this pin is
–100
–20
–40
–60
–80
100
80
60
40
20
0
–50
–
Reference Voltage Temperature
Coefficient
(Pin 2/Pin 4): Pin 2, the positive side of the
V
REF
–25
AT 0 = 2.500V
IN
–
), is alternately driven between V
0
TEMPERATURE (°C)
terminals. To prevent start-up prob-
OUT
25
+
, Pin 2 sources current from V
. In all cases current flow in the
50
OUT
LT1054/LT1054L
75
. When driven to ground,
LT1054 • TPC10
100
125
OUT
OUT
(Pin 5)
+
Pin 4
1054lfe
and
5
+
+
.