cat5271 ON Semiconductor, cat5271 Datasheet
cat5271
Related parts for cat5271
cat5271 Summary of contents
Page 1
... The device can be programmed shutdown state during operation. The CAT5271 operates from 2 5.5 V, while consuming less than 2 mA. This low operating current, combined with a small package footprint, makes the CAT5271 ideal for battery−powered portable applications ...
Page 2
... Table 1. ORDERING INFORMATION Part Number Resistance CAT5271ZI−50−GT3 50 kW CAT5271ZI−00−GT3 100 kW †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Table 2. PIN FUNCTION DESCRIPTION Pin No. ...
Page 3
Table 4. ELECTRICAL CHARACTERISTICS and 100 kW Versions –40°C < Parameter DC CHARACTERISTICS — RHEOSTAT MODE Resistor Differential ...
Page 4
Table 5. CAPACITANCE T = 25° 1.0 MHz Symbol C Input/Output Capacitance (SDA, SCL) I/O (Note 11) Table 6. POWER UP TIMING (Notes 11 and 12) Symbol t Power−up to Read Operation ...
Page 5
DNL 0.01 0 −0.01 −0.02 −0.03 −0.04 −0. 128 160 TAP Figure 2. Differential Non−Linearity 5 120 100 5.6 V ...
Page 6
TEMPERATURE (°C) Figure 7. Change in End−to−End Resistance 0 −6 V − −18 −24 −30 − (KHz) Figure 9. Gain vs. Bandwidth (Tap 0x80) ...
Page 7
... R of the FET switch connecting the ON wiper output with its respective contact point. In CAT5271 this ‘contact’ resistance is typically 50 W. Thus a connection setting of 0x00 yields a minimum resistance between terminals W and B. For a 100 kW device, the second connection, or the first tap ...
Page 8
... Input GND Potentiometer GND Figure 12. ESD Protection Networks Terminal Voltage Operating Range The CAT5271 V and GND power supply define the DD limits for proper 3−terminal digital potentiometer operation. Signals or potentials applied to terminals the wiper must remain inside the span which attempt to go outside these boundaries will be clamped by the internal forward biased diodes ...
Page 9
... When the CAT5271 READ mode it transmits 8 bits of data, releases the SDA line, and monitors the line for an acknowledge. Once it receives this acknowledge, the CAT5271 will continue to transmit data acknowledge is sent by the Master, the device terminates data transmission and waits for a STOP condition ...
Page 10
SDA SCL START CONDITION SCL FROM MASTER DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER START Figure 16. Start/Stop Condition 1 Figure 17. Acknowledge Condition http://onsemi.com 10 STOP CONDITION 8 9 ACKNOWLEDGE ...
Page 11
... INSTRUCTION AND REGISTER DESCRIPTION SLAVE ADDRESS BYTE The first byte sent to the CAT5271 from the master/processor is called the Slave Address Byte. The most significant seven bits of the slave address are a device type identifier. For the CAT5271, these bits are fixed at 0101111. The following bit (R/W) selects between a Read or a Write operation ...
Page 12
E E1 TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-187. PACKAGE DIMENSIONS MSOP 10, 3x3 CASE 846AE−01 ISSUE O SYMBOL MIN A A1 0.00 ...
Page 13
... N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 13 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative CAT5271/D ...