24lc16bt-st Microchip Technology Inc., 24lc16bt-st Datasheet
24lc16bt-st
Related parts for 24lc16bt-st
24lc16bt-st Summary of contents
Page 1
... Microchip Technology Inc. 24AA16/24LC16B 2 ™ C Serial EEPROM Description: Temp. The Microchip Technology Inc. 24AA16/24LC16B Ranges (24XX16 Kbit Electrically Erasable PROM. The device is organized as eight blocks of 256 x 8-bit (1) I memory with a 2-wire serial interface. Low-voltage I, E design permits operation down to 1.7V with standby and active currents of only 1 μ ...
Page 2
... CC = +1.7V to +5. +2.5V to +5.5V CC Conditions — — — (Note 3 OUT 5.0V (Note 25° MHz A CLK V = 5.5V, SCL = 400 kHz CC — Industrial Automotive SDA = SCL = © 2007 Microchip Technology Inc. ...
Page 3
... This eliminates the need for a 4: This parameter is not tested but ensured by characterization. For endurance estimates in a specific application, please consult the Total Endurance™ Model which can be obtained from Microchip’s web site at www.microchip.com. © 2007 Microchip Technology Inc. 24AA16/24LC16B Industrial (I -40°C to +85°C, V ...
Page 4
... FIGURE 1-1: BUS TIMING DATA 5 3 SCL 7 6 SDA 14 IN SDA OUT FIGURE 1-2: BUS TIMING START/STOP SCL 6 7 SDA Start DS21703G-page Stop © 2007 Microchip Technology Inc. ...
Page 5
... DATA TRANSFER SEQUENCE ON THE SERIAL BUS (A) (B) SCL SDA Start Condition © 2007 Microchip Technology Inc. 24AA16/24LC16B 3.4 Data Valid (D) The state of the data line represents valid data when, after a Start condition, the data line is stable for the duration of the high period of the clock signal. ...
Page 6
... Block Select Code Read Block Address 1010 Write Block Address 1010 DS21703G-page 6 FIGURE 3-2: Control Code Start Bit ’ code, the R CONTROL BYTE ALLOCATION Read/Write Bit Block Select Bits R/W ACK Slave Address Acknowledge Bit © 2007 Microchip Technology Inc. ...
Page 7
... Bus Activity Block Select Bits © 2007 Microchip Technology Inc. 24AA16/24LC16B 4.2 Page Write The write control byte, word address and the first data byte are transmitted to the 24XX16 in the same way byte write. However, instead of generating a Stop condition, the master transmits data bytes to ...
Page 8
... Send Start Send Control Byte with R Did Device No Acknowledge (ACK = 0)? Yes Next Operation DS21703G-page 8 6.0 WRITE PROTECTION The WP pin allows the user to write-protect the entire array (000-7FF) when the pin is tied the write protection is disabled. SS © 2007 Microchip Technology Inc tied to CC ...
Page 9
... A Master R T SDA Line S Bus Activity © 2007 Microchip Technology Inc. 24AA16/24LC16B 7.3 Sequential Read Sequential reads are initiated in the same way as a random read, except that once the 24XX16 transmits the first data byte, the master issues an acknowledge as opposed to a Stop condition in a random read. This directs the 24XX16 to transmit the next sequentially- addressed 8-bit word (Figure 7-3) ...
Page 10
... Byte B1B0 Block K K Select Bits Bits Data ( Data ( Data ( Data ( © 2007 Microchip Technology Inc. ...
Page 11
... SCL low. Changes during SCL high are reserved for indicating Start and Stop conditions. 8.2 Serial Clock (SCL) The SCL input is used to synchronize the data transfer to and from the device. © 2007 Microchip Technology Inc. 24AA16/24LC16B TSSOP DFN MSOP SOT-23 ...
Page 12
... NNN 8-Lead MSOP XXXXXT YWWNNN 8-Lead 2x3 DFN XXX YWW NN 5-Lead SOT-23 XXNN DS21703G-page 12 Example: 24LC16B e I/P 3 13F 0527 Example: 24LC16BI 0527 13F Example: 4L16 I527 13F Example: 4L16I 52713F Example: 254 527 13 Example: B53F © 2007 Microchip Technology Inc. ...
Page 13
... Note: Please visit www.microchip.com/Pbfree for the latest information on Pb-free conversion. *Standard OTP marking consists of Microchip part number, year code, week code, and traceability code. © 2007 Microchip Technology Inc. 24AA16/24LC16B 1st Line Marking Codes SOT-23 MSOP I Temp ...
Page 14
... E1 .240 D .348 L .115 c .008 b1 .040 b .014 eB – c NOM MAX 8 – .210 .130 .195 – – .310 .325 .250 .280 .365 .400 .130 .150 .010 .015 .060 .070 .018 .022 – .430 Microchip Technology Drawing C04-018B © 2007 Microchip Technology Inc. ...
Page 15
... Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. © 2007 Microchip Technology Inc. 24AA16/24LC16B D e ...
Page 16
... REF: Reference Dimension, usually without tolerance, for information purposes only. DS21703G-page Units MILLIMETERS Dimension Limits MIN NOM N e 0.65 BSC A – A2 0.80 1.00 A1 0.05 E 6.40 BSC E1 4.30 4.40 D 2.90 3.00 L 0.45 0.60 L1 1.00 REF φ 0° c 0.09 b 0.19 φ L MAX 8 – 1.20 1.05 – 0.15 4.50 3.10 0.75 – 8° – 0.20 – 0.30 Microchip Technology Drawing C04-086B © 2007 Microchip Technology Inc. ...
Page 17
... Package may have one or more exposed tie bars at ends. 3. Package is saw singulated. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. © 2007 Microchip Technology Inc. 24AA16/24LC16B ...
Page 18
... REF: Reference Dimension, usually without tolerance, for information purposes only. DS21703G-page Units MILLIMETERS Dimension Limits MIN NOM 0.65 BSC A – – A2 0.75 0.85 A1 0.00 – E 4.90 BSC E1 3.00 BSC D 3.00 BSC L 0.40 0.60 L1 0.95 REF φ 0° – c 0.08 – b 0.22 – Microchip Technology Drawing C04-111B φ L MAX 1.10 0.95 0.15 0.80 8° 0.23 0.40 © 2007 Microchip Technology Inc. ...
Page 19
... Lead Width Notes: 1. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.127 mm per side. 2. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. © 2007 Microchip Technology Inc. 24AA16/24LC16B ...
Page 20
... Revised Figure 3-2 Control Byte Allocation; Figure 4-1 Byte Write; Figure 4-2 Page Write; Section 6.0 Write Protection; Figure 7-1 Current Address Read; Figure 7- 2 Random Read; Figure 7-3 Sequential Read; Section 8.3 Write-Protect (WP). Revision G (02/2007) Changed 1.8V to 1.7V; Revised Features Section; Replaced Package Drawings; Revised Product ID Section. DS21703G-page 20 © 2007 Microchip Technology Inc. ...
Page 21
... To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions. © 2007 Microchip Technology Inc. 24AA16/24LC16B CUSTOMER SUPPORT Users of Microchip products can receive assistance through several channels: • ...
Page 22
... What deletions from the document could be made without affecting the overall usefulness there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS21703G-page 22 Total Pages Sent ________ FAX: (______) _________ - _________ N Literature Number: DS21703G © 2007 Microchip Technology Inc. ...
Page 23
... To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office PART NO. X /XX Device Temperature Package Range 24AA16: = 1.7V, 16 Kbit I 24AA16T: = 1.7V, 16 Kbit I (Tape and Reel) 24LC16B: = 2.5V, 16 Kbit I 24LC16BT: = 2.5V, 16 Kbit I (Tape and Reel) Temperature I = -40°C to +85°C Range -40°C to +125°C Package 2x3 DFN, 8-lead P ...
Page 24
... NOTES: DS21703G-page 24 © 2007 Microchip Technology Inc. ...
Page 25
... Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. © 2007 Microchip Technology Inc. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, K ...
Page 26
... Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2007 Microchip Technology Inc. EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris ...