tb6595fl ETC-unknow, tb6595fl Datasheet
tb6595fl
Related parts for tb6595fl
tb6595fl Summary of contents
Page 1
... Toshiba Bi-CD Integrated Circuit Silicon Monolithic Dual-Bridge Driver IC for DC motor TB6595FL/FLG is a quad-bridge driver IC for DC motor with output transistor in LD MOS structure with low ON-resistor. Two input signals, IN1 and IN2, can chose one of four modes such as CW, CCW, short brake, and stop mode.. ...
Page 2
... BIN2 20 BPWM 19 STBYC 1 CIN1 4 Control Logic C CIN2 3 CPWM 2 STBYD 28 DIN1 25 Control Logic D DIN2 26 DPWM H-Bridge H-Bridge TSD H-Bridge H-Bridge 2 TB6595FL/FLG VM1 11 AO1 13 A AO2 10 PGNDA 12 VM2 16 BO1 14 B BO2 17 PGNDB 15 VM3 35 CO1 33 C CO2 36 PGNDC 34 VM4 30 DO1 32 D DO2 ...
Page 3
... L H Ｈ OFF (High impedance OFF (High impedance) L OUT1 Ｍ OUT2 GND <ALL OFF> t2=500ns (Typ.) 3 TB6595FL/FLG Output OUT2 Mode Ｌ Short brake Ｈ Forward/reverse L Short brake Ｌ Forward/reverse L Short brake Stop Stand-by (Power save) OUT2 OUT1 Ｍ GND < ...
Page 4
... Symbol Rating Unit −0 0.8 A OUT P 0. − °C opr −55 to 150 T °C stg °C) Symbol Min Typ. Max 5 V 2.7 5 2.2 5 5.5 ⎯ ⎯ Iout 0.6 4 TB6595FL/FLG Remark IN1, IN2, PWM, STBY Note1 Unit 2006-3-6 ...
Page 5
... INSL = 0. sat ( ( (Not tested) ∆ TB6595FL/FLG = 25°C) CC Min Typ. Max Unit ⎯ 1.8 1.3 ⎯ 1.8 mA 1.3 ⎯ 1.8 1.3 ⎯ ⎯ 10 µA ⎯ ⎯ ⎯ 0.2 −0.2 ⎯ ...
Page 6
... Control 25 H-SW D DIN2 Logic 26 D DPWM GND PG4 PG3 , V , and GND lines since the IC may be destroyed TB6595FL/FLG + VM2 VM1 16 11 AO1 AO2 1 10 BO1 BO2 2 17 CO1 CO2 ...
Page 7
... When mounting or soldering, take care to ensure that neither static electricity nor electrical overstress is applied to the IC (measures to prevent anti-static, leaks, etc.). • When incorporating into a set, adopt a set design that does not apply voltage directly to the island section. (Lower surface) 7 TB6595FL/FLG 2006-3-6 ...
Page 8
... Package Dimensions QON-36-P-0606-0.50 Weight: 0.08 g (typ.) Unit : mm 8 TB6595FL/FLG 2006-3-6 ...
Page 9
... Otherwise, the current or power consumption may exceed the absolute maximum rating, and exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. In addition, do not use any device that is applied the current with inserting in the wrong orientation or incorrectly even just one time. 9 TB6595FL/FLG 2006-3-6 ...
Page 10
... If the current sink capability of the power supply is small, the device’s motor power supply and output pins might be exposed to conditions beyond maximum ratings. To avoid this problem, take the effect of back-EMF into consideration in system design. 10 TB6595FL/FLG ) J 2006-3-6 ...
Page 11
... TB6595FL/FLG 2006-3-6 ...