atmega323l ATMEL Corporation, atmega323l Datasheet - Page 198
atmega323l
Manufacturer Part Number
atmega323l
Description
Atmega323 8-bit Avr Microcontroller With 32k Bytes Of In-system Programmable Flash
Manufacturer
ATMEL Corporation
Datasheet
1.ATMEGA323L.pdf
(247 pages)
- Current page: 198 of 247
- Download datasheet (4Mb)
Data Polling Flash
Data Polling EEPROM
198
ATmega323(L)
3. The Serial Programming instructions will not work if the communication is out of
4. If a chip erase is performed (must be done to erase the Flash), wait 2•t
5. The Flash is programmed one page at a time. The memory page is loaded one
6. The EEPROM array is programmed one byte at a time by supplying the address
7. Any memory location can be verified by using the Read instruction which returns
8. At the end of the programming session, RESET can be set high to commence
9. Power-off sequence (if needed):
When a page is being programmed into the Flash, reading an address location within
the page being programmed will give the value $FF. At the time the device is ready for a
new page, the programmed value will read correctly. This is used to determine when the
next page can be written. Note that the entire page is written simultaneously and any
address within the page can be used for polling. Data polling of the Flash will not work
for the value $FF, so when programming this value, the user will have to wait for at least
t
all locations, programming of addresses that are meant to contain $FF, can be skipped.
See Table 68 t
When a new byte has been written and is being programmed into EEPROM, reading the
address location being programmed will give the value $FF. At the time the device is
ready for a new byte, the programmed value will read correctly. This is used to deter-
mine when the next byte can be written. This will not work for the value $FF, but the user
should have the following in mind: As a Chip Erased device contains $FF in all locations,
programming of addresses that are meant to contain $FF, can be skipped. This does
not apply if the EEPROM is re-programmed without Chip Erasing the device. In this
case, data polling cannot be used for the value $FF, and the user will have to wait at
least t
WD_FLASH
synchronization. When in sync. the second byte ($53), will echo back when issu-
ing the third byte of the Programming Enable instruction. Whether the echo is
correct or not, all four bytes of the instruction must be transmitted. If the $53 did
not echo back, give SCK a positive pulse and issue a new Programming Enable
command. If the $53 is not seen within 32 attempts, there is no functional device
connected.
after the instruction, give RESET a positive pulse, and start over from Step 2.
See Table 68 for the t
byte at a time by supplying the 6 LSB of the address and data together with the
Load Program memory Page instruction. The Program memory Page is stored
by loading the Write Program memory Page instruction with the 8 MSB of the
address. If polling is not used, the user must wait at least t
ing the next page. (Please refer to Table 68). Accessing the Serial Programming
interface before the Flash write operation completes can result in incorrect
programming.
and data together with the appropriate Write instruction. An EEPROM Memory
location is first automatically erased before new data is written. If polling is not
used, the user must wait at least t
refer to Table 68). In a chip erased device, no $FFs in the data file(s) need to be
programmed.
the content at the selected address at serial output MISO/PB6.
normal operation.
Set XTAL1 to “0” (if a crystal is not used).
Set RESET to “1”.
Turn V
WD_EEPROM
before programming the next page. As a Chip Erased device contains $FF in
CC
power off
WD_FLASH
before programming the next byte. See Table 68 for t
.
WD_FLASH
figure.
WD_EEPROM
before issuing the next byte. (Please
WD_FLASH
WD_EEPROM
before issu-
1457G–AVR–09/03
WD_FLASH
.
Related parts for atmega323l
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: