sc16311 Silan, sc16311 Datasheet
sc16311
Related parts for sc16311
sc16311 Summary of contents
Page 1
... It consists of 12 segment output lines, 8 grid output lines, 8 segment/grid output drive lines, a display memory, a control circuit, and a key scan circuit. Serial data is input to the SC16311 through a three- line serial interface. This FIP controller/driver is ideal as a peripheral device of a single-chip microcomputer. ...
Page 2
... LED, IOH1=-1mA LED, IOL1=20mA DOUT, IOL2=4mA -2V, Seg1~Seg12 -2V, Grid1~Grid8 Seg13/Grid16 ~Seg18/Grid11 VO= V -35V, driver off DD driver output VI VSS DD CLK, DIN, STB Under no load, display off SC16311 Value -0.5~ +7.0 +0.5 ~V -40 DD +0.5 DD -0.5~V +0.5 DD +25 -40(grid) 1200* -40~+85 -65~+150 = Typ. Max ...
Page 3
... CL=300pF, Segn, Gridn Duty = 50 =4.5~5.5V Test conditions CLK STB CLK CLK SC16311 SC16311 = - Min. Typ. Max. 350 500 650 300 100 2 0.5 120 1 15 Min. Typ. Max 400 1 100 100 Grid 6 ...
Page 4
... Clock input, Reads serial data at rising edge, and outputs data at falling edge. Strobe, Initializes serial interface at rising or falling edge to make SC16311waiting for reception of command. Data input after STB has fallen is processed as command. While command data is processed, current processing is stopped, and serial interface is initialized. While STB is high, CLK is ignored ...
Page 5
... FUNCTION DESCRIPTION Display RAM Address and Display Mode The display RAM stores the data transmitted from an external device to theSC16311 through the serial interface, and is assigned addresses as follows, in units of 8 bits: Seg1 Seg4 Seg8 00HL 00HU 03HL 03HU 06HL 06HU 09HL 09HU ...
Page 6
... Command A command sets the display mode and status of the FIP driver. The first 1 byte input to theSC16311 through the DIN pin after the STB pin has fallen is regarded as a command. If STB is made high while a command/data is transmitted, serial communication is initialized, and the command/data being transmitted is invalid (however, the command/data already transmitted remains valid). ...
Page 7
... Writes data to display memory. 01:Writes data to LED port. 10:Reads key data. 11: Reads SW data. Sets address increment mode(display memory). 0:Increments address after data has been written. 1:Fixes address Sets test mode 0: Normal operation 1: Test mode LSB Address (00H-2FH) SC16311 REV:1.0 2004.08.03 Page ...
Page 8
... Sets pulse width to 10/16. 100: Sets pulse width to 11/16. 101: Sets pulse width to 12/16. 110: Sets pulse width to 13/16. 111: Sets pulse width to 14/16. Turns on/off display. 0: Display off(key scan continues*) 1: Display on TDISP 500 s ......... DIGn 1/16 TDISP 1 frame = TDISP SC16311 key scan data ... DIG1 REV:1.0 2004.08.03 Page ...
Page 9
... WAIT Data reading command is set PW CLK CLK t CLK-STB t HOLD t PZL t t THZ TZH 90% 10% SC16311 If data is contiguous Data reading starts. PW STB t PLZ REV:1.0 2004.08.03 Page ...
Page 10
... Data transfers display data (48 bytes max.) Command 4: controls display Updating specific address STB CLK Command Command 1: sets data Command 2: sets address Data: display data HANGZHOU MICROELECTRONICS CO.,LTD Http: www.silan.com.cn Command Command Data Command Command Data 2 SC16311 Command Data n 4 Data 2 REV:1.0 2004.08.03 Page ...
Page 11
... Persons at a work bench should be earthed via a wrist strap. Equipment cases should be earthed. All tools used during assembly, including soldering tools and solder baths, must be earthed. MOS devices should be packed for dispatch in antistatic/conductive containers. HANGZHOU MICROELECTRONICS CO.,LTD Http: www.silan.com.cn SC16311 UNIT mm REV:1.0 2004.08.03 Page ...