lb11993w Sanyo Semiconductor Corporation, lb11993w Datasheet - Page 3

• Manufacturer Part Number: lb11993w
• Description: For Digital Video Camera Three-phase Brushless 3-in-1 Motor Driver
• Manufacturer: Sanyo Semiconductor Corporation

Continued from preceding page.
Note 1: Design target value parameters are not tested.
Note 2: The standard for the overlap amount parameter is to report the measured value without change.
Cylinder Motor Driver Block at Ta=25 C, V CC 1=3V, V CC 2=4.75V, VS=3V
Note 1: Design target value parameters are not tested.
[FRC pin]
High-level voltage
Low-level voltage
Input current
Leakage current
[VH]
Hall supply voltage
Minus (-) pin voltage
[FG comparator]
Input offset voltage
Input bias current
Input bias current offset
Common-mode input range
High-level output voltage
Low-level output voltage
Voltage gain
Output current (sink)
Supply current 4
Output quiescent current 4
Output quiescent current 5
Output saturation voltage upper side 1
Output saturation voltage lower side 1
Output saturation voltage upper side 2
Output saturation voltage lower side 2
COM pin common-mode input voltage
range
Standby pin high-level voltage
Standby pin low-level voltage
Standby pin input current
Standby pin leakage current
FRC pin high-level voltage
FRC pin low-level voltage
FRC pin input current
FRC pin leakage current
Slope pin source current ratio
Slope pin sink current ratio
CSLP1 source-to-sink current ratio
CSLP2 source-to-sink current ratio
Startup frequency
Phase delay width
Parameter
Parameter
VFRCH
VFRCL
IFRCIN
IFRCLK
VHALL
VH(-)
VFGOFF
IbFG
VFGCM
VFGOH
VFGOL
VGFG
IFGOs
IbFG
Symbol
I CC 2
I CC 2Q
IS(D)Q
VOU1
VOD1
VOU2
VOD2
VIC
VSTBYH
VSTBYL
ISTBYH
ISTBYL
VFRCH
VFRCL
IFRCI
IFRCL
RSOURCE
RSINK
RCSLP1
RCSLP2
Freq
Dwidth
Symbol
VFRC_C=3V
VFRC_C=0V
I H =5mA, VH(+)-VH(-)
I H =5mA
VFGIN+=VFGIN-=1.5V
VFGIN+=VFGIN-=1.5V
When internally pulled up
When internally pulled up
Design target value, Note 1
Output pin set to low
I O =76mA, VSTBY_D=3V
VSTBY_C=0V
VSTBY_D=VSTBY_C=0V
VSTBY_D=VSTBY_C=0V
I O =0.1A, RF=0.25
I O =0.1A, RF=0.25
I O =0.4A, VS=3V, RF=0.25
I O =0.4A, VS=3V, RF=0.25
VSTBY_D=3V
VSTBY_D=0V
VFRC_D=3V
VFRC_D=0V
ICSLP1SOURCE/ICSLP2SOURCE
ICSLP1SINK/ICSLP2SINK
ICSLP1SOURCE/ICSLP1SINK
ICSLP2SOURCE/ICSLP2SINK
Cosc=0.1 F, OSC frequency
Design target value, Note 1
Design target value, Note 1
LB11993W
Conditions
Conditions
min
0.83
0.90
-100
-0.2
2.5
1.2
2.8
-3
min
-0.2
-0.2
-10
-10
-20
-20
-35
-35
0.3
2
2
Ratings
typ
0.93
0.97
Ratings
100
20
typ
0.75
11.5
100
0.2
0.2
0.3
0.3
30
max
V CC 2-0.9
V CC 1
max
1.03
1.04
500
100
-30
V CC 1
V CC 1
0.4
2.5
0.2
40
+3
5
100
300
2.5
0.4
0.4
0.6
0.6
0.7
0.7
No.A0677-3/15
50
50
20
20
15
15
Unit
mV
mA
nA
nA
dB
V
V
V
V
V
V
V
Unit
deg
mA
A
A
Hz
%
%
%
%
V
V
V
V
V
V
V
V
V
A
A
A
A
A
A