msm9026 ETC-unknow, msm9026 Datasheet - Page 6

• Manufacturer Part Number: msm9026
• Description: Emulation Board S1207
• Manufacturer: ETC-unknow

MOSEL VITELIC
To prepare voice file(s)
To prepare up to 32 voice files by MES 2.0 or 3.0.
These files must be 8-bit PCM file.
To prepare a filled PRF
To write down your demand options on PRF (product
request form) is strongly recommended before you
are running 9026pack.exe.
To prepare a source text
Using commercial text editor on personal computer,
you can set up a source text in the format defined in
9026pack software user's manual (pid 392 10/96). In
this source text, you can define the both word
sections and sentence tables. This source text must
have the file extension .SRC. Most of mask options
can be defined on the screen in 9026pack.exe. The
entry dependent options could be defined inside
source text.
To have a compiled binary file
Running 9026pack.exe and entering keystrokes as
prompt, you can easily define the options and read in
the source text. Completing as the screen tells, you
can get a compiled binary file in your specified file
name. Its file extension is always .BIN.
To have 27C010 programmed
Programming this .BIN file into an 27C010 chip by
commercial EPROM programmer, you have it ready.
To insert this 27C010
To insert this EPROM chip into textool U3 of 9026
board in right direction.
To set up LED selections
To set up LED connection by jumper 3x5 if needed.
To set up Trigger Drive
To set up trigger drive circuit as your requirement on
jumper 3x6. Without the drive source (either high or
low, either R or bare wire) the switch keeps floating
and never be capable to activate the trigger. Without
right polarity of drive source you can neither trigger
the sound and you may hurt this 9026 board.
Before Operating 9026
Taiwan
#1, Creation Road I,
Science - based Industrial Park,
Hsinchu, 30077
Taiwan, ROC
"[e-mail]"
TEL: [phone]
FAX: [phone]
FAX: [phone]
Taipei
7F, #102 Sec. 3,
Ming Chung E. Road,
Taipei,105
Taiwan, ROC
TEL: [phone]
FAX: [phone]
6/6
To configure demanded wires
Ensuring you have both 1.5Vx4 power and speaker
well connected, this board are ready to work. There
are push-button switches to turn on or off the power.
Red LED lamp D3 tells the power on. JP2 enables the
auto power off function.
Operation Flow
Warning
Output pin definition restricted: If you select LED
dynamic flash, then the M9026 output level will remain
the same as the output level of the previous entry.
Trigger pin definition restricted: M9026 performs
two trigger options only, active high & pull low & low
latch as well as active low & pull high & high latch.
The M9026 debounce time (min. trigger pulse width) is
shown as table in page 3/6, not optional as chip.
Misc
Source Text .SRC
Fuse : Not Available
Power : 1.5V x 4 (battery) or 6 VDC power supply
Dimension : (LxWxH) 160x115x20 mm
Weight : 150 g
Demonstration Kit
Hongkong
#19 Dai
Taipo Industrial Estate,
Taipo, N.T.
Hongkong
TEL: [phone](MKO)
TEL: [phone]
FAX: [phone]
FAX: [phone](MKO)
Get Output file filename.BIN
filled Product Request Form
Get 27C010 programmed
Go EPROM programmer
Insert onto 9026 board
and file filename.OPT
Run 9026PACK.EXE
Fu Street,
textool included
Voice files
U.S.A.
#3910 North First Street,
San Jose,
CA. 65134-1501
U.S.A.
TEL: [phone]
FAX: [phone]
MSM9026
PID342 10/96