sky65152-11 Skyworks Solutions, Inc., sky65152-11 Datasheet

no-image

sky65152-11

Manufacturer Part Number
sky65152-11
Description
Sky65152-11 2.4-2.5 Ghz Wlan Power Amplifier
Manufacturer
Skyworks Solutions, Inc.
Datasheet
DATA SHEET
SKY65152-11: 2.4-2.5 GHz WLAN Power Amplifier
Applications
Features
RF_IN
IEEE 802.11 b/g WLANs
ISM band transmitters
WCS fixed wireless
Wireless access nodes
EVM < 2.5% for P
High gain = 32 dB
Internal RF match with DC block and active bias circuits
Internal on/off control circuit
Internal, high dynamic range power detector
Single DC supply = +5 V
Operating temperature = –40 °C to +85 °C
Small, MCM (20-pin, 6 x 6 mm) package (MSL3, 260 C per
JEDEC J-STD-020)
Match
Skyworks offers lead (Pb)-free RoHS (Restriction of
Hazardous Substances) compliant packaging.
Input
R
Figure 1. SKY65152-11 Block Diagram
REF1
VREF1
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200968F • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 19, 2009
OUT
VCC1
VC_BIAS
> +27 dBm
Match
Stage
Inter-
R
REF2
Active Bias
VREF2
VCC2
PA_ENB
Match
Inter-
Stage
R
REF3
VREF3
VCC3
VCC_DET
Detector
Output
Match
RF_OUT
V_DET
S1503
Description
The SKY65152-11 is a Microwave Monolithic Integrated Circuit
(MMIC) Power Amplifier (PA) with superior output power, linearity,
and efficiency. These features make the SKY65152-11 ideal for
Wireless Local Area Network (WLAN) applications. The high
linearity (low EVM) and high efficiency of this device makes it
ideal for use in the transmit chain of WLAN access points or
modems.
The SKY65152-11 is fabricated using Skyworks high reliability
Heterojunction Bipolar Transistor (HBT) InGaP process, which
allows for single supply operation while maintaining high
efficiency and good linearity. The device is internally matched and
mounted in a 20-pin, 6 x 6 mm Multi-Chip Module (MCM)
Surface-Mounted Technology (SMT) package, which allows for a
highly manufacturable low cost solution.
A functional block diagram is shown in Figure 1. The pin
configuration and package are shown in Figure 2. Signal pin
assignments and functional pin descriptions are provided in
Table 1.
VC_BIAS
PA_ENB
VREF1
VREF2
GND
GND
Figure 2. SKY65152-11 Pinout – 20-Pin MCM
1
2
3
4
5
6
20
7
(Top View)
19
8
18
9
17
10
16
15
14
13
12
11
VCC1
VCC_DET
V_DET
VCC2
N/C
VCC3
S1504
1

Related parts for sky65152-11

sky65152-11 Summary of contents

Page 1

... The SKY65152- Microwave Monolithic Integrated Circuit (MMIC) Power Amplifier (PA) with superior output power, linearity, and efficiency. These features make the SKY65152-11 ideal for Wireless Local Area Network (WLAN) applications. The high linearity (low EVM) and high efficiency of this device makes it ideal for use in the transmit chain of WLAN access points or modems ...

Page 2

... Resistors R1, R2, and R3 on the Evaluation Board set the correct bias to these pins when attached power supply. The SKY65152-11 includes an internal PA enable control pin (pin 3) for fast RF on/off control. Zero volts turns off the PA while enables the PA. The device also provides an output power detector voltage, V_DET, at pin 14 ...

Page 3

... Table 2. SKY65152-11 Absolute Maximum Ratings (Note 1) Parameter RF output power Supply voltage (VCC, VC_BIAS, and PA_ENB) (Note 2) Total supply current Reference voltage (Note 2) Detector supply voltage (VCC_DET) (Note 2) Power dissipation Case temperature Storage temperature Junction temperature Thermal resistance Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value ...

Page 4

... DATA SHEET • SKY65152-11 POWER AMPLIFIER Table 4. SKY65152-11 Electrical Specifications (Note 1) (VCC1 = VCC2 = VCC3 = VREF1 = VREF2 = VREF3 = VC_BIAS = VCC_DET = PA_ENB = 5 V, Characteristic Impedance [ °C, Frequency = 2.442 GHz, Unless Otherwise Noted Parameter IEEE 802.11g Orthogonal Frequency Division Multiplexing Input Signal, Data Rate = 54 Mbps ...

Page 5

... MHz 2442 MHz 2412 MHz +23 +24 +25 +26 +27 +28 +40 +30 +20 +10 0 –10 –20 –30 –40 2.5 3.0 3.5 4.0 0 DATA SHEET • SKY65152-11 POWER AMPLIFIER 2410 2420 2430 2440 2450 2460 2470 Frequency (MHz) Figure 4. Small Signal Gain vs Frequency 800 Total 600 ...

Page 6

... DATA SHEET • SKY65152-11 POWER AMPLIFIER +10 0 –10 –20 –30 –40 –50 2.412 2.422 2.432 2.442 Frequency (GHz) Figure 9. Spectral Response @ P (802.11g, OFDM, 64 QAM @ 54 Mbps +12 +14 +16 +18 +20 +22 +24 +26 P (dBm) OUT Figure 11. PAE vs Output Power –40 – ...

Page 7

... The following design considerations are general in nature and must be followed regardless of final use or configuration: 1. Paths to ground should be made as short as possible. 2. The ground pad of the SKY65152-11 has special electrical and thermal grounding requirements. This pad is the main thermal conduit for heat dissipation. Since the circuit board acts as the heat sink, it must shunt as much heat as possible from the device ...

Page 8

... J3 GND GND Figure 16. SKY65152-11 Evaluation Board Assembly Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 8 October 19, 2009 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200968F ...

Page 9

... Figure 17. SKY65152-11 Evaluation Board Layer Detail Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200968F • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 19, 2009 DATA SHEET • SKY65152-11 POWER AMPLIFIER ...

Page 10

... DATA SHEET • SKY65152-11 POWER AMPLIFIER Figure 18. Evaluation Board Layer Detail Physical Characteristics Table 5. SKY65152-11 Evaluation Board Bill of Materials Component Value C1, C2, C6 3300 pF 0603 C5, C7, C8, C10 8.2 pF 0603 10 μF C11, C15, C16, C17 0603 0603 560 Ω R1 0603 180 Ω R2, R3 0603 300 Ω ...

Page 11

... DC blocking capacitor. All impedance matching is provided internal to the module. Package Dimensions The PCB layout footprint for the SKY65152-11 is shown in Figure 19. Typical case markings are shown in Figure 20. Package dimensions for the 20-pin MCM are shown in Figure 21, and tape and reel dimensions are provided in Figure 22. ...

Page 12

... Side View (0.1) 0.875 0.875 Metal Pad Edge Detail B Scale CCW Figure 21. SKY65152-11 20-Pin MCM Package Dimensions = Manufacture Year 4X 2.5 8X 2.9 16X Solder Mask Opening See Detail C 0 Bottom View 0.875 0.2 x 0.2 0.875 Solder Mask Edges 15X Detail C Scale: 2X Pin 20 ...

Page 13

... For all other MCM/RFLGA products, pin 1 orientation is in top right corner. Figure 22. SKY65152-11 20-Pin MCM Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200968F • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 19, 2009 DATA SHEET • ...

Page 14

... DATA SHEET • SKY65152-11 POWER AMPLIFIER Ordering Information Model Name SKY65152-11 WLAN Power Amplifier Copyright © 2009 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer ...

Related keywords