at86rf210 ATMEL Corporation, at86rf210 Datasheet

no-image

at86rf210

Manufacturer Part Number
at86rf210
Description
At86rf210 Z-link? Transceiver
Manufacturer
ATMEL Corporation
Datasheet
Features
Applications
Description
The Atmel AT86RF210 Z-Link
transceiver capable of transmitting and receiving BPSK modulated digital data over a
frequency range of 868 MHz and 902–928 MHz using a minimum number of external
components. It combines excellent RF performance with low cost, small size and low
current consumption. The AT86RF210 includes a crystal stabilized Fractional-N syn-
thesizer, BPSK transmitter and receiver, and full Direct Sequence Spread Spectrum
Signal (DSSS) processing, including spreading and despreading. The device is fully
compatable with IEEE 802.15.4 and ZigBee standards. It includes internal voltage
regulation and battery monitoring circuitry and requires a minimum number of external
support components.
Figure 1. Block Diagram
Sw Out
850–930 MHz Output Frequency
Rx Current: 14.5 mA
Low Sleep Mode Current: 1 uA
DSSS Processing and BPSK Modulation/Demodulation
Battery Voltage Monitoring Circuitry
4 mW (6 dBm) Min. Transmit Power @ Vdd = 1.8V
Serial Peripheral Interface (SPI) Control
Power Supply Voltage Operating Range: 1.8V to 3.6V
Low External Component Count
48QFN Package
Low Band IEEE 802.15.4/ZigBee
Industrial, Commercial, Home Lighting Control, Security, and HVAC
Inventory Management
Health Monitoring
Wireless PC Peripherals such as Mouse, Keyboard, and Joystick
Consumer Electronics Remote Controls and Toys
Tx Out
Ant In
Sw In
Rx In
Power Amp
Low Noise
T/R Switch
Amp
I/Q Mixer
X
Polyphase
Modulator
Filter
Transceiver is a fully integated, low-cost ZigBee
Synthesizer
-based Systems
IF Amp
Spreader
Data In
Demodulator
Despreader
SPI Bus
SDO
Data Out
SDI
SCLK
SEL
AT86RF210
Z-Link
Transceiver
868/902–928 MHz
Direct Sequence
Spread Spectrum
BPSK Transceiver
Preliminary
5033AS–WIRE–10/03

Related parts for at86rf210

at86rf210 Summary of contents

Page 1

... MHz and 902–928 MHz using a minimum number of external components. It combines excellent RF performance with low cost, small size and low current consumption. The AT86RF210 includes a crystal stabilized Fractional-N syn- thesizer, BPSK transmitter and receiver, and full Direct Sequence Spread Spectrum Signal (DSSS) processing, including spreading and despreading ...

Page 2

... Maximum Input Voltage...........................................VDD + 0.5V Maximum Operating Voltage (VDD ) ................................... 4,5 Table 2. Operating Conditions Symbol Parameter TAMB Operating temperature VSUPPLY Voltage supply range HUMIDITY Humidity Note: Unit operation is guaranteed by design when operating within these ranges. AT86RF210 2 Reg Filter VDDD VSSA VSSD Image P Reject P Filter F M ...

Page 3

... Min Typ Max 850 930 100 100 0 30 1.2 600 1.0 105 30 AT86RF210 Unit Unit MHz Ohm dBm dB dBm dBm dBm dBm dBm usec usec dB dB MHz KHz dB dB Kb/s uA/dB dBm 3 ...

Page 4

... Crystal oscillator settling time TSynth Phase locked loop settling time Synthres Synthesizer tuning resolution . Table 7. Serial Configuration Register* Symbol Parameter TRISE CMOS input rise time TFALL CMOS input fall time TCLKS CLK setup time AT86RF210 4 Min Typ 0.25 25 1.8 ...

Page 5

... External filter cap for the VCO regulator NA Pin not used NA Pin not used NA VCO power supply ground A_I NA LO VCO control input. An internal differential varactor diode tunes the LO frequency. The control voltage should be referenced to LOGND. AT86RF210 Typ Max 25 Min Typ Max 1.5 3.5 Unit nsec ...

Page 6

... No Connect 41 PPFREG 42 V_I/O RSSI 43 A_0 XTALMODE 44 D_IO CCA 45 D_O AT86RF210 6 Startup Cond Description NA Charge pump output NA Analog synthesizer ground NA Analog synthesizer power supply NA Crystal oscillator input 1. One side of oscillator crystal is connected to this pin. NA Crystal oscillator input 2. When internal oscillator is used, this pin has crystal connected ...

Page 7

... Analog (RF) power supply ground LNA external inductor. Collector inductor for LNA. P/O RF tuning network. • RF_I RF input • RF_I/O RF input/output • Voltage_I/O Voltage input/output • V_I Voltage input • A_I Analog input • A_O Analog output • D_I Digital input • D_O Digital output AT86RF210 7 ...

Page 8

... Note: With pin 44 (Xstal_Sel) low RF210 uses system clock from controller With pin 44 (Xstal_Sel) high RF210 uses external crystal placed across pin 22 & 23 AT86RF210 8 R0 TBD C23 10n 36 START (DIGITAL INTERFACE) 35 VSSDIG 34 VDDDIG AT86RF210 x 31 SYSCLK 30 SELl 29 SCLK 28 SDO 27 SDI (FREQUENCY GENERATION INTERFACES connect 25 TXDAT R2 TBD C4 ...

Page 9

... Orchard Parkway San Jose, CA 95131 R 5033AS–WIRE–10/ Top View Bottom View TITLE 48QN1, 48-lead 7.0 x 7.0 mm Body, 0.50 mm Pitch, Quad Flat No Lead Package (QFN) AT86RF210 Side View COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 7.00 BSC E 7 ...

Page 10

... Fax: (81) 3-3523-7581 Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibil ity for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time wit h out notice, and does not make any commitment to update the information contained herein ...

Related keywords