emc2103-3-kp-tr Standard Microsystems Corp., emc2103-3-kp-tr Datasheet - Page 67
emc2103-3-kp-tr
Manufacturer Part Number
emc2103-3-kp-tr
Description
Emc2103 Rpm-based Fan Controller With Hardware Thermal Shutdown
Manufacturer
Standard Microsystems Corp.
Datasheet
1.EMC2103-3-KP-TR.pdf
(85 pages)
- Current page: 67 of 85
- Download datasheet (2Mb)
RPM-Based Fan Controller with HW Thermal Shutdown
Datasheet
SMSC EMC2103
6.37
6.38
ADDR
ADDR
E5h
E4h
R/W
R/W
R/W
R/W
The GPIO Input Register indicates the state of the corresponding GPIO pin. When a GPIO is
configured as an input, any change of state will assert the ALERT# pin (unless GPIO interrupts are
masked, see
Bit 1 - GPIO2_IN - Indicates the pin state of the GPIO2 pin regardless of the pin functionality.
Bit 0 - GPIO1_IN - Indicates the pin state of the GPIO1 pin regardless of the pin functionality.
The GPIO Output Register controls the state of the corresponding pins when they are configured as
outputs.
If the output is configured as an open-drain output, then it requires a pull-up resistor to VDD. Setting
the corresponding bit to a ‘1’ will act to disable the output allowing the pull-up resistor to pull the output
high. Setting the corresponding bit to a ‘0’ will enable the output and drive the pin to a logical ‘0’ state.
If the output is configured as a push-pull output, then output pin will immediately be driven to match
the corresponding bit setting.
Bit 1 - GPIO2_OUT - Controls the pin state of the GPIO2 pin when it is configured as a GPIO output.
Bit 0 - GPIO1_OUT - Controls the pin state of the GPIO1 pin when it is configured as a GPIO output.
The GPIO Interrupt Enable Register enables the GPIOs to assert the ALERT pin when they change
state. When the GPIO pins are configured as outputs, then these bits are ignored.
Bit 1 - GPIO2_INT_EN - Allows the ALERT pin to be asserted when the GPIO2 pin changes state
(when configured as an input).
Bit 0 - GPIO1_INT_EN - Allows the ALERT pin to be asserted when the GPIO1 pin changes state
(when configured as an input).
GPIO Output Register (EMC2103-2 Only)
GPIO Interrupt Enable Register (EMC2103-2 Only)
‘0’ (default) - The ALERT pin will not be asserted when the GPIO2 pin changes state (when
configured as an input).
‘1’ - The ALERT pin will be asserted when the GPIO2 pin changes state (when configured as an
input)
‘0’ (default) - The ALERT pin will not be asserted when the GPIO1 pin changes state (when
configured as an input).
REGISTER
Interrupt
REGISTER
Enable
GPIO
Output 1
GPIO
Section
Table 6.55 GPIO Interrupt Enable Register
6.15).
B7
-
B7
-
Table 6.54 GPIO Output Register
B6
-
B6
-
DATASHEET
B5
B5
67
B4
B4
B3
B3
B2
B2
GPIO2_
INT_EN
GPIO2
B1
_OUT
B1
GPIO1_
INT_EN
GPIO1
Revision 0.88 (06-30-08)
_OUT
B0
B0
DEFAULT
DEFAULT
00h
00h
Related parts for emc2103-3-kp-tr
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Interface, Integrated USB2.0 Compatible 3-Port Hub
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Lan91c100fd Rev. B Feast Fast Ethernet Controller With Full Duplex Capability
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Feast ? Ast Ethernet Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Com20022i 10 Mbps Arcnet Ansi 878.1 Controller With 2k X 8 On-chip Ram
Manufacturer:
Standard Microsystems Corp.
Part Number:
Description:
Lpc47n207 Lpc Super I/o Irda Hot Docking Chip With Uart Data Brief
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Advanced I/o With X-bus Interface
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Fdc37m707 Enhanced Super I/o Controller With Wake-up Features
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Twenty Pin Uart Tpuart Corporation
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Enhanced Small Device Interface Controller
Manufacturer:
Standard Microsystems Corp.
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Emc1001 1.5?c Smbus Temperature Sensor In Miniature Sot-23
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Beta Compensation And Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Multiple Temperature Sensor With Beta Compensation And Hottest Of Thermal Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Resistance Error Correction & Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet: