am42-0002 Tyco Electronics, am42-0002 Datasheet - Page 2

• Manufacturer Part Number: am42-0002
• Description: Gaas Mmic Vsat Power Amplifier 1.4w
• Manufacturer: Tyco Electronics

2
Absolute Maximum Ratings
M/A-COM Inc. and its affiliates reserve the right to make changes to the
product(s) or information contained herein without notice. M/A-COM makes
no warranty, representation or guarantee regarding the suitability of its
products for any particular purpose, nor does M/A-COM assume any liability
whatsoever arising out of the use or application of any product(s) or
information.
GaAs MMIC VSAT Power Amplifier 1.4 W
14.0 - 14.5 GHz
Electrical Specifications: T
1.
2.
3.
Handling Procedures
Please observe the following precautions to avoid
damage:
Static Sensitivity
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
devices.
Saturated Output Power
Detector Output Voltage
Power Added Efficiency
Output Power at P1dB
Exceeding any one or combination of these limits may cause
permanent damage to this device.
M/A-COM does not recommend sustained operation near
these survivability limits.
Case Temperature (T
Channel Temperature
Storage Temperature
Thermal Resistance
RF Input Power
Output VSWR
Parameter
Input VSWR
Bias Current
Parameter
Linear Gain
Output IP3
V
V
GG
DD
C
) = +25°C.
Two +24 dBm output tones @ 1 MHz spacing
Absolute Maximum
-65°C to +150°C
A
1,2,3
-10 Volts
+23 dBm
R
12 Volts
150°C
= 25°C, V
L
= 10 K Ω, P
Test Conditions
25°C Heat Sink
P
P
P
P
P
P
IN
IN
IN
IN
IN
IN
= +14 dBm
= +14 dBm
= +14 dBm
< 0 dBm
< 0 dBm
< 0 dBm
—
OUT
DD
= +31 dBm
= +9 V, V
Compliant
• North America Tel: [phone] / Fax: [phone]
• Europe Tel: [phone] / Fax: [phone]
• Asia/Pacific Tel: [phone] / Fax: [phone]
Visit www.macom.com for additional data sheets and product information.
Application Schematic
4.
5.
6.
7.
8.
9.
GG
Nominal bias is obtained by first connecting –5 volts to pin
4 (V
Note sequence.
RF ground and thermal interface is the flange (case bot-
tom). Adequate heat sinking is required.
No DC bias voltage appears at the RF ports.
The DC resistance at the input port is an open circuit and
at the output port is a short circuit.
For optimum IP3 performance, the V
should be placed within 0.5 inches of pin 6.
Resistor and capacitors surrounding the amplifier are
suggestions and not included as part of the AM42-0002.
RoHS
= -5.0 V, Z
GG
), followed by connection +9 volts to pin 6 (V
Units
Ratio
Ratio
°C/W
dBm
dBm
dBm
mA
dB
%
V
0
= 50 Ω
Min.
30.5
19
—
—
—
—
—
—
—
—
4,5,8,9
DD
Typ.
2.5:1
2.7:1
31.5
29.5
+3.5
800
22
39
22
10
bypass capacitors
AM42-0002
Max.
DD
2.7:1
1400
—
—
—
—
—
—
—
—
).
V4