afbr-53d3 Avago Technologies, afbr-53d3 Datasheet - Page 2

• Manufacturer Part Number: afbr-53d3
• Description: Rohs Compliant 850 Nm Vcsel 1x9 Fiber Optic Transceivers For Fibre Channel
• Manufacturer: Avago Technologies

Package and Handling Instructions
Flammability
The AFBR-53D3 transceiver family housing is made of
high strength, heat resistant, chemically resistant, and
UL 94V-0 flame retardant plastic.
Recommended Solder and Wash Process
The AFBR-53D3 transceiver family is compatible with
industry-standard wave or hand solder processes.
Process plug
This transceiver is supplied with a process plug (HFBR-
5000) for protection of the optical ports within the
duplex SC connector receptacle. This process plug
prevents contamination during wave solder and
aqueous rinse as well as during handling, shipping and
storage. It is made of a hightemperature, molded
sealing material that can withstand +80°C and a rinse
pressure of 110 lbs per square inch.
Recommended Solder fluxes
Solder fluxes used with the AFBR-53D3 should be
water-soluble, organic fluxes. Recommended solder
fluxes include Lonco 3355-11 from London Chemical
West, Inc. of Burbank, CA, and 100 Flux from Alpha-
Metals of Jersey City, NJ.
Recommended Cleaning/Degreasing Chemicals
Alcohols: methyl, isopropyl, isobutyl.
Aliphatics: hexane, heptane. Other: soap solution,
naphtha. Do not use partially halogenated
hydrocarbons such as 1,1.1 trichloroethane, ketones
such as MEK, acetone, chloroform, ethyl acetate,
methylene dichloride, phenol, methylene chloride, or
N-methylpyrolldone. Also, Avago Technologies does
not recommend the use of cleaners that use
halogenated hydrocarbons because of their potential
environmental harm.
Regulatory Compliance
(See the Regulatory Compliance Table for transceiver
performance) The overall equipment design will
determine the certification level. The transceiver
performance is offered as a figure of merit to assist the
designer in considering their use in equipment designs.
2
Electrostatic Discharge (ESD)
There are two design cases in which immunity to ESD
damage is important. The first case is during handling
of the transceiver prior to mounting it on the circuit
board. It is important to use normal ESD handling
precautions for ESD sensitive devices. These
precautions include using grounded wrist straps, work
benches, and floor mats in ESD controlled areas. The
transceiver performance has been shown to provide
adequate performance in typical industry production
environments. The second case to consider is static
discharges to the exterior of the equipment chassis
containing the transceiver parts. To the extent that the
duplex SC connector receptacle is exposed to the
outside of the equipment chassis it may be subject to
whatever system-level ESD test criteria that the
equipment is intended to meet. The transceiver
performance is more robust than typical industry
equipment requirements of today.
Electromagnetic Interference (EMI)
Most equipment designs utilizing these high-speed
transceivers from Avago Technologies will be required
to meet the requirements of FCC in the United States,
CENELEC EN55022 (CISPR 22) in Europe and VCCI in
Japan. Refer to EMI section (page 5) for more details.
Immunity
Equipment utilizing these transceivers will be subject
to radio-frequency electromagnetic fields in some
environments. These transceivers have good immunity
to such fields due to their shielded design.
Eye Safety
These laser-based transceivers are classified as AEL
Class I (U.S. 21 CFR(J) and AEL Class 1 per EN 60825-1
(+A11). They are eye safe when used within the data
sheet limits per CDRH. They are also eye safe under
normal operating conditions and under all reasonably
foreseeable single fault conditions per EN60825-1.
Avago Technologies has tested the transceiver design
for compliance with the requirements listed below
under normal operating conditions and under single
fault conditions where applicable. TUV Rheinland has
granted certification to these transceivers for laser eye
safety and use in EN 60950 and EN 60825-2
applications. Their performance enables the
transceivers to be used without concern for eye safety
up to 7 V transmitter VCC.