glc110 SL Power Electronics, glc110 Datasheet

glc110

Manufacturer Part Number

glc110

Description

Glc110 Commercial/glm110 Medical 110 Watt Global Performance Switchers

Manufacturer

SL Power Electronics

Datasheet

1.GLC110.pdf (2 pages)

Current page: 1 of 2
Download datasheet (227Kb)

GLC110

110 Watt Global Performance Switchers

SPECIFICATIONS:

Ac Input

90-264 Vac, 47-63 Hz single phase.

Input Current

Maximum input current at 90 Vac, 60 Hz with full rated

output load not to exceed 2.9 A.

Hold-up Time

20 ms minimum from loss of ac input at full load, nominal

line (120 Vac).

Output Power

Normal continuous output power is 75 W for unrestricted

natural convection, or 110 W with 26 cfm air flow.

Output Regulation

Load regulation on dual output models is measured by

±40% load change from 60% rated load and input

voltage change from minimum to maximum ratings.

Output #1 requires 1A minimum load for proper regula-

tion of other outputs. Initial set tolerance is measured with

all outputs at 60% of full rated load. Load regulation for

single-output models measured by changing load from

5% to 50% load or 50% to full load in either direction.

Voltage Adjustment

Output #1 adjustment is ±5%. Note: output #1 must not be

more than 1% below nominal to achieve full output

regulation on output #2. High voltage settings may

degrade the reliability of the unit due to excessive power

dissipation in some outputs.

Overload Protection

Fully protected against short circuit and output overload.

Short circuit protection is cycling type power limit. Factory

set to begin power limiting at 120 W.

Output Noise

0.5% rms, 1% pk-pk, 20 MHz bandwidth, differential

mode. Measured with noise probe directly across output

terminals of the power supply.

POWER FAIL

Power fail signal is TTL or CMOS compatible (output goes

low <0.5 V) 5 ms before output voltage drops more than

4% below nominal voltage upon loss of AC power. The

signal is factory set to trip on 84 to 94 Vac brown-out

depending upon incoming line impedance and distortion.

Commercial/GLM110 Medical

Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033

800-235-5929 • 805-486-4565 • FAX 805-487-8911 • www.condorpower.com

FEATURES:

• Cost-effective power source

• Single- and multiple-output units

• Low height (1.30")

• 2-year warranty

• Power fail signal standard

• Commercial Approved to UL1950, IEC950

• Medical Approved to UL2601-1, EN60601,

• Complies with EN61000-3-2 Class A

•

Other settings are available to the user through adjust-

ment of built in potentiometer (consult factory for assis-

tance). Output will stay low for 20 ms minimum.

Transient Response

Main Output: 500 µs typical response time for return to

within 0.5% of final value for a 50% load step change, i/

shutdown overshoot less than 3%.

Turn-On Time

Less than 1 second at 120 Vac, 25

Overvoltage Protection

Built in on main output.

Efficiency

72-85% depending on model.

Input Protection

Internal ac fuse provided on all units. Designed to blow

only if a catastrophic failure occurs in the unit.

Inrush Current

Inrush limited by internal thermistors. Inrush at 240 Vac,

averaged over the first ac half-cycle under cold start

conditions will not exceed 37 A.

Temperature Coefficient

0.03%/°C typical on all outputs.

EMI/EMC Compliance

All models include built-in EMI filtering to meet the

following emissions requirements:

EMI SPECIFICATIONS

Conducted Emissions GLC110 EN55022 Class B; FCC Class B

Conducted Emissions GLM110 EN55011 Class B; FCC Class B

Static Discharge

RF Field Susceptibility

Fast Transients/Bursts

Surge Susceptibility

Line Frequency Harmonics

Commercial Safety

All GLC models are approved to UL1950, CSA22.2 No.

234 Level 3, IEC950 and EN60950. Consult factory for

approval status.

Medical Safety

All GLM models are approved to UL2601-1, CSA-C22.2 No.

601.1, IEC601-1/60601-1. Consult factory for approval status.

t<0.2 A/µs. Maximum voltage deviation is 3.5%. Startup/

CSA22.2 No. 234

CSA-C22.2 No. 601.1

marked to LVD

EN61000-4-5, 1 kV diff., 2 kV com.

COMPLIANCE LEVEL

EN61000-4-2, 6 kV contact, 8 kV air

EN61000-4-4, 2 kV, 5 kHz

EN61000-3-2 Class A

EN61000-4-3, 3 V/meter

Related parts for glc110

glc110 Summary of contents

Page 1

... EMI/EMC Compliance All models include built-in EMI filtering to meet the following emissions requirements: EMI SPECIFICATIONS COMPLIANCE LEVEL Conducted Emissions GLC110 EN55022 Class B; FCC Class B Conducted Emissions GLM110 EN55011 Class B; FCC Class B Static Discharge EN61000-4- contact air RF Field Susceptibility EN61000-4-3, 3 V/meter ...

Page 2

... A. Rating with unrestricted convection cooling. Total power not to exceed output can exceed rated current. B. Rating with 26 cfm forced air cooling. Total power not to exceed 110 maintain regulation V1 current must be at least 1/5 of V2. V1 must not be adjusted more than 1% below nominal and have at least 10% of rated load. GLC110/GLM110 MECHANICAL SPECIFICATIONS E ...

Related keywords

glc110 datasheet
glc110 data sheet
glc110 pdf datasheet
glc110 component
glc110 part
glc110 distributor
glc110 RoHS
glc110 datasheet download